background image

5

English

Indoor Unit 

1.

Installing the mounting plate.

• The mounting plate should be installed on a wall which can support the weight of the indoor unit.

1) Temporarily secure the mounting plate to the wall, make sure that the panel is completely level, and mark the boring 

points on the wall.

2) Secure the mounting plate to the wall with screws.

Recommended mounting plate retention spots and Dimensions

2.

Boring a wall hole and installing wall embedded pipe.

• For walls containing metal frame or metal board, be sure to use a wall embed-

ded pipe and wall cover in the feed-through hole to prevent possible heat, 
electrical shock, or fire.

• Be sure to caulk the gaps around the pipes with caulking material to prevent 

water leakage.
1) Bore a feed-through hole of 65mm in the wall so it has a down slope toward 

the outside.

2) Insert a wall pipe into the hole.
3) Insert a wall cover into wall pipe.
4) After completing refrigerant piping, wiring, and drain piping, caulk pipe hole 

gap with putty.

105

273

52

41.5

51

85

41.5

60

65

85

734

50

269

110

95

(Bolt size : M10)

(Bolt size : M10)

Recommended mounting plate
retention spots (6 spots in all)

Leveling mounting plate

Dangle a weighted thread 
and align thread with
vertical arrow.

a

Place a leveler 
on raised tab.

b

Use tape measure 
as shown.

Position the end of 
tape measure at 

∇.

Unit outline

(unit: mm)

Gas pipe end

Liquid pipe end

Through-the-wall 
hole ø65mm

Drain hose position

Removed pipe 
port cover

* The removed pipe port cover can be
   kept in the mounting plate pocket

Mounting plate

A

Inside

Outside

Caulking

Wall embedded pipe 
(Field supply)

Wall hole cover
(Field supply)

Wall embedded pipe 
(Field supply)

φ

65

01_EN_3P147083-2F.fm  Page 5  Friday, October 28, 2005  9:29 AM

Summary of Contents for FTN25DAV3B

















Reviews: