Daikin EKCBX008BBV3, Operation Manual

Page: 13 / 24

EKCBX/H008BBV3
Unit for air to water heat pump system
4PW67442-1A – 12.2010
Operation manual
12
Consulting programmed actions
Consulting space heating or domestic water heating actions
Consulting space heating or domestic water heating is carried out as
follows.
1 Press the
<
button.
The actual mode is blinking.
2 Use the
pi
and
pj
buttons to select the mode you want
to program (space heating h or domestic water heating w )
3 Press the
<
button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to consult by means of the pi
and pj buttons.
The selected day is blinking.
5 Press the
<
button to confirm the selected day.
The first programmed action of the selected day appears.
6 Use the pi and pj buttons to consult the other
programmed actions of that day.
This is called the readout mode. Empty program actions (e.g. 3
and 4) are not displayed.
By pressing the
pr
button several times, you return to previous
steps in this procedure and finally return to normal operation.
Consulting space cooling, quiet mode, or booster heater mode
Consulting space cooling, quiet mode, or booster heater modeis
carried out as follows.
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to consult (space cooling c , quiet mode s , or booster heater
mode m .
The selected mode is blinking.
3 Press the
<
button to confirm the selected mode.
The first programmed action is displayed.
4 Use the pi and pj buttons to consult the programmed
actions.
This is called the readout mode. Empty program actions (e.g. 3
and 4) are not displayed.
By pressing the
pr
button several times, you return to previous
steps in this procedure and finally return to normal operation.
Tips and tricks
Programming the next day(s)
After confirming the programmed actions of a specific day (i.e. after
pressing the
<
button for 5 seconds), press the
pr
button once. You
can now select another day by using the
pi
and
pj
buttons
and restart consulting and programming.
Copying programmed actions to next day
In heating/domestic water heating program it is possible to copy all
programmed actions of a specific day to the next day (e.g. copy all
programmed actions from "
1
" to "
2
").
To copy programmed actions to the next day, proceed as follows:
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to program.
The selected mode is blinking.
You can leave programming by pressing the
pr
button.
3 Press the
<
button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to copy to the next day by means
of the
pi and pj buttons.
The selected day is blinking.
You can return to step
2 by pressing the
pr
button.
5 Press the
<
and
pr
buttons simultaneously for 5 seconds.
After 5 seconds the display will show the next day (e.g. " 2 " if
" 1 " was selected first). This indicates that the day has been
copied.
You can return to step
2 by pressing the pr button.
Deleting one or more programmed actions
Deleting one or more programmed actions is done at the same time
as storing the programmed actions.
When all actions for one day have been programmed, make sure that
the display shows the highest action number you would like to save.
By pressing the
<
button for 5 seconds, you store all actions except
those with a higher action number than the one that is displayed.
E.g. when the < button is pressed when action number 3 is
displayed, actions 1, 2 and 3 are stored but 4 is deleted.
Deleting a mode
1 Press the
<
button.
The actual mode is blinking.
2 Use the
pi
and
pj
buttons to select the mode you want
to delete (space cooling
c
, quiet mode s , or booster heating
mode m ).
The selected mode is blinking.
3 Press the < and ba button simultaneously for 5 seconds to
delete the selected mode.
Deleting a day of the week (space heating or domestic water
heating mode)
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to delete (space heating h or domestic water heating w ).
The selected mode is blinking.
3 Press the
<
button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to delete by means of the pi
and pj buttons.
The selected day is blinking.
5 Press the
<
and
ba
button simultaneously for 5 seconds to
delete the selected day.
INFORMATION
Returning to previous steps in this procedure is done by
pressing the
pr
button.
INFORMATION
Returning to previous steps in this procedure is done by
pressing the
pr
button.