Installation manual
40
EKCBX/H008BBV3
Unit for air to water heat pump system
4PW66983-1C – 08.2011
14. O
PERATION
OF
THE
UNIT
Once the unit is installed and test operation of outdoor unit and
indoor units is finished, the operation of the unit can start.
For operating the indoor unit, the user interface of the indoor unit
should be switched ON. Refer to the indoor unit operation manual for
more details.
15. M
AINTENANCE
AND
SERVICE
15.1. Maintenance introduction
In order to ensure optimal operation of the unit, a number of checks
and inspections should be carried out on the unit at regular intervals,
preferably yearly.
This maintenance must be carried out by your local Daikin
technician.
To execute the maintenance activities as mentioned below, it is
required to open the outdoor unit covers. See "Opening the outdoor
unit" as well as the indoor unit front panel, See
15.2. Maintenance activities
Service precautions
Checks
The described checks must be executed at least once a year.
1.
Water pressure
Check if the water pressure is above 1 bar. If necessary add
water.
2.
Water filter
Clean the water filter.
3.
Water pressure relief valve
Check for correct operation of the pressure relief valve by
turning the red knob on the valve counter-clockwise:
-
If you do not hear a clacking sound, contact your local dealer.
-
In case the water keeps running out of the unit, close both
the water inlet and outlet shut-off valves first and then contact
your local dealer.
4.
Domestic hot water tank pressure relief valve (field supply)
Applies only to installations with a domestic hot water tank.
Check for correct operation of the pressure relief valve on the
domestic hot water tank.
5.
Domestic hot water tank pressure relief valve (field supply)
Applies only to installations with a domestic hot water tank.
Check for correct operation of the pressure relief valve on the
domestic hot water tank.
6.
Domestic hot water tank booster heater
Applies only to installations with a domestic hot water tank.
It is advisable to remove lime buildup on the booster heater to
extend its life span, especially in regions with hard water. To do
so, drain the domestic hot water tank, remove the booster heater
from the domestic hot water tank and immerse in a bucket (or
similar) with lime-removing product for 24 hours.
7.
Outdoor unit and indoor unit switch box
-
Carry out a thorough visual inspection of the switch box
(in- and outdoor unit) and look for obvious defects such as
loose connections or defective wiring.
-
Check for correct operation of contactors K1M, K2M, K3M,
K5M (applications with domestic hot water tank only) and
K4M by use of an ohmmeter. All contacts of these contactors
must be in open position.
INFORMATION
■
When the program is stopped by an error, by an
operation switch off or by a power failure, then the
U3
error will be displayed.
To resolve the error codes, see
In this case [F-09] (Latest action number executed)
will contain the latest action executed.
■
[F-08] The "Underfloor heating screed dry-out
program enabled (1)/disabled (0)" is always set to 0
(disable) when a program has been started once. This
means that in case a second time an underfloor
heating screed dry-out program must be started then
[F-08] needs to be set again.
DANGER: ELECTRICAL SHOCK
"2. General safety precautions" on page 2
■
Before carrying out any maintenance or repair activity,
always switch off the circuit breaker on the supply
panel, remove the fuses or open the protection
devices of the unit.
■
Make sure that before starting any maintenance or
repair activity, also the power supply to the outdoor
unit is switched off.
■
Do not touch live parts for 10 minutes after the power
supply is turned off because of high voltage risk.
■
The heater of the compressor may operate even in
stop mode.
■
Please note that some sections of the electric
component box are hot.
■
Make sure you do not touch a conductive section.
■
Do not rinse the indoor unit. This may cause electric
shocks or fire.
■
When service panels are removed, live parts can be
easily touched by accident.
Never leave the unit unattended during installation or
servicing when service panel is removed.
CAUTION: Play it safe!
Touch a metal part by hand (such as the stop valve) in
order to eliminate static electricity and to protect the PCB
before performing service.
DANGER: DO NOT TOUCH PIPING AND INTERNAL
PARTS
See
"2. General safety precautions" on page 2
Do not touch water pipes during and immediately after
operation as the pipes may be hot. Your hand may suffer
burns. To avoid injury, give the piping time to return to
normal temperature or be sure to wear proper gloves.
WARNING
■
Do not touch the refrigerant pipes during and
immediately after operation as the refrigerant pipes
may be hot or cold, depending on the condition of the
refrigerant flowing through the refrigerant piping,
compressor, and other refrigerant cycle parts. Your
hands may suffer burns or frostbite if you touch the
refrigerant pipes. To avoid injury, give the pipes time to
return to normal temperature or, if you must touch
them, be sure to wear proper gloves.
■
Do not touch the internal parts (pump, backup heater,
etc.) during and immediately after operation. Your
hands may suffer burns if you touch the internal parts.
To avoid injury, give the internal parts time to return to
normal temperature or, if you must touch them, be
sure to wear proper gloves.
