Daikin EBHQ006BAV3, Operation Manual

Page: 12 / 20

Operation manual
11
0 EKCBX/H008BAV3
Unit for air to water heat pump system
4PW64603-1A – 08.2010
Tips and tricks
Programming the next day(s)
After con fi rming the programmed actions of a speci fi c day (i.e. after
pressing the < button for 5 seconds), press the pr button once. You
can now select another day by using the pi and pj buttons
and restart consulting and programming.
Copying programmed actions to next day
In heating/cooling program it is possible to copy all programmed
actions of a speci
fi c day to the next day (e.g. copy all programmed
actions from " 1 " to " 2 ").
To copy programmed actions to the next day, proceed as follows:
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to program.
The selected mode is blinking.
You can leave programming by pressing the pr button.
3 Press the < button to con fi rm the selected mode.
The actual day is blinking.
4 Select the day you would like to copy to the next day by means
of the
pi and pj buttons.
The selected day is blinking.
You can return to step 2 by pressing the pr button.
5 Press the < and pr buttons simultaneously for 5 seconds.
After 5 seconds the display will show the next day (e.g. " 2 " if
" 1 " was selected fi rst). This indicates that the day has been
copied.
You can return to step 2 by pressing the pr button.
Deleting one or more programmed actions
Deleting one or more programmed actions is done at the same time
as storing the programmed actions.
When all actions for one day have been programmed, make sure that
the display shows the highest action number you would like to save.
By pressing the
< button for 5 seconds, you store all actions except
those with a higher action number than the one that is displayed.
E.g. when the < button is pressed when action number 3 is
displayed, actions 1, 2 and 3 are stored but 4 and 5 are deleted.
Deleting a mode
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to delete (quiet mode s , booster heating m or domestic water
heating w ).
The selected mode is blinking.
3 Press the < and ba button simultaneously for 5 seconds to
delete the selected mode.
Deleting a day of the week (cooling or heating mode)
1 Use the = button to select the operation mode (cooling or
heating) you want to delete.
2 Press the < button.
The actual mode is blinking.
3 Press the < button to con fi rm the selected mode.
The actual day is blinking.
4 Select the day you would like to delete by means of the pi
and pj buttons.
The selected day is blinking.
5 Press the < and ba button simultaneously for 5 seconds to
delete the selected day.
4.3. Field settings
The indoor unit shall be con fi gured by the installer to match the
installation environment (outdoor climate, installed options, etc.) and
user demand. However, the
fi eld settings mentioned in "Field settings
table" on page 15 can be modi fi ed to customer preferences. Thereto,
a number of so called fi eld settings are available. These fi eld settings
are accessible and programmable through the user interface on the
indoor unit.
Each fi eld setting is assigned a 3-digit number or code, for example
[1-03], which is indicated on the user interface display. The fi rst digit
[1] indicates the ' fi rst code' or fi eld setting group. The second and
third digit [03] together indicate the 'second code'.
A list of all fi eld settings and default values is given under "Field
settings table" on page 15 . In this same list, we provided for 2
columns to register the date and value of altered fi eld settings at
variance with the default value.
A detailed description of each fi eld setting is given under "Detailed
description" on page 12 .
Procedure
To change one or more fi eld settings, proceed as follows.
1 Press the z button for a minimum of 5 seconds to enter FIELD
SET MODE.
The
$ icon (3) will be displayed. The current selected fi eld
setting code is indicated ; (2), with the set value displayed to
the right - (1).
2 Press the bgi button to select the appropriate fi eld setting
fi rst code.
3 Press the bgj button to select the appropriate fi eld setting
second code.
4 Press the pfi button and pfj button to change
the set value of the select fi eld setting.
NOTICE
The default values mentioned in "Field settings table" on
page 15 are the values from factory. The actual initial
values shall be selected according to your application.
These values shall be con
fi rmed by your installer.
CAUTION
The fi eld settings [2] depends on the relevant local and
national regulations.
The fi eld settings [9] depends on the application.
Before changing these settings, the new values shall be
con
fi rmed by the installer and/or shall be according to the
local and national regulations.
2
3
1