SiK011003
37
Operation Manual
Operation Manual
2.1.1.9 TURBO button
When pressing this button under cooling or heating mode, air conditioner will enter into quick cooling or quick heating mode. The character
of "
" is displayed on remote controller. Press this button again to exit turbo function and the character of "
" will be disappeared on
remote controller.
2.1.1.10 SLEEP button
Press this button under cooling, heating or drying mode can start up sleep function. " " icon will be displayed on remote controller. Press
this button again to cancel sleep function. " "icon on remote controller will be displayed.
2.1.1.8 TIMER button
● At ON status, press this button once to set TIMER OFF. The character of HOUR and OFF will flash. Press the "+" or "-" button within 5s to
adjust the time of TIMER ON. Each time the "+" or "-" button is pressed, time will increase or decrease by half an hour. When holding the "+"
or "-" button for at least 2s, the time will change quickly until the required time is reached. After that, press the "TIMER" button to confirm it.
The character of HOUR and OFF won’t flash again. Cancel TIMER OFF: Press the "TIMER" button again under TIMER OFF status.
● At OFF status, press this button once to set TIMER ON. Please refer to TIMER OFF for detailed operation. Cancel TIMER ON: Press the
"TIMER" button again under TIMER ON status.
Note:
● Time setting range: 0.5-24 hours.
● Time interval between two operations can’t exceed 5s, otherwise the remote controller will exit the setting status automatically.
● The TIMER OFF function is resetted when the CHILD LOCK function is unlocked.
2.1.1.11 LIGHT button
Press this button to turn on or turn off display light on indoor unit.
2.1.2.1 Child lock function
Press "+" and "-" buttons simultaneously can turn on or turn off child lock function. When child lock function is started up, " " icon will be
displayed on remote controller. If operate remote controller, " " icon will flash three times, while remote controller won’t send signal.
2.1.2.2 Switchover function for temperature display
After turning off the unit by remote controller, press "-" button and "MODE" button simultaneously to switch between °Cand °F .
2.1.3.1 Press the back side of remote controller marked with "
", as shown in the fig,
and then push out the cover of battery box along the arrow direction.
2.1.3.2 Replace two 7# (AAA 1.5V) dry batteries, and make sure the position of "+" polar
and "-" polar are correct.
2.1.3.3 Reinstall the cover of battery box.
Note:
● During operation, point the remote control signal sender at the receiving window on indoor unit.
● The distance between signal sender and receiving window should be no more than 8m, and there should be no obstacles between them.
● Signal may be interfered easily in the room where there is fluorescent lamp or wireless telephone; remote controller should be close to
indoor unit during operation.
● Replace new batteries of the same model when replacement is required.
● When you don’t use remote controller for a long time, please take out the batteries.
● If the display on remote controller is fuzzy or there’s no display, please replace batteries.
● After putting through the power, press "ON/OFF" button on remote controller toturn on the air conditioner.
● Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT.
● Press "+" or "-" button to set your required temperature. (Temperature can’t be adjusted under auto mode).
● Press "FAN" button to set your required fan speed: auto, low, medium and highspeed.
● Press "SWING" button to select fan blowing angle.
2.1.2 Introduction to functions of combination buttons
2.1.3 Operation Guide
2.1.4 Replacement of Batteries in Remote Controller
signal sender
battery
Cover of battery box
remove
reinstall
Note:
● After starting up X-FAN function, when turning off the unit, indoor fan will continue to operate for a while at low speed to dry the residual
water inside the indoor unit.
● When the unit operates under X-FAN mode, press "X-FAN" button can turn off X-FAN function. Indoor fan stops operation immediately.
