background image

ARC412 Series

Si10-416A

184

Operation

Setting dry batteries

1. Slide the back cover of the remote controller in the direction of 

the arrow and take it off.

2. Set two dry batteries in accordance with the indications of (+) and (–).

Note on batteries

1

Use two LR03 (AAA) batteries.

1

Never mix new and old batteries or different type of batteries.

1

Never try to charge the batteries.

1

Used-up batteries must be taken out all at once and disposed-off properly.

1

In case the remote controller will not be used for a long time take

out all batteries in order to prevent liquid leak from the batteries.

1

Batteries life is about a year under normal use conditions.

 Replace the batteries with new ones when, on pressing a button, 
 the display shows all figures at the same time and the remote 
 controller does not send signals to the air conditioner.

Address switch

1

Address switch is used for the installation of 2 units in one room.

 Contact the shop you purchased this DAIKIN room air conditioner 
 if you would like to have 2 units/room.

1

Signals cannot be received if the address switch selects a signal 
different from that of the main unit.

Summary of Contents for ARC412A6

















Reviews: