Daikin Altherma EHYHBH05A Series Installer'S Reference Manual Download Page 84

Page: 84 / 264

Piping installation

Installer reference guide

08CA + EHY EHYHBH/X08A + EHYKOMB33AA

Daikin Altherma hybrid heat pump

4P355634-1G – 2022.09

8 Piping installation

CAUTION

See

"4 Specific installer safety instructions"

[

21] to make sure this installation

complies with all safety regulations.

In this chapter

8.1

Preparing refrigerant piping ...................................................................................................................................................

8.1.1

Refrigerant piping requirements ...........................................................................................................................

8.1.2

Refrigerant piping insulation..................................................................................................................................

8.2

Connecting the refrigerant piping..........................................................................................................................................

8.2.1

About connecting the refrigerant piping...............................................................................................................

8.2.2

Precautions when connecting the refrigerant piping............................................................................................

8.2.3

Guidelines when connecting the refrigerant piping..............................................................................................

8.2.4

Pipe bending guidelines .........................................................................................................................................

8.2.5

To flare the pipe end..............................................................................................................................................

8.2.6

To braze the pipe end ............................................................................................................................................

8.2.7

Using the stop valve and service port....................................................................................................................

8.2.8

To connect the refrigerant piping to the outdoor unit .........................................................................................

8.2.9

To connect the refrigerant piping to the indoor unit............................................................................................

8.3

Checking the refrigerant piping..............................................................................................................................................

8.3.1

About checking the refrigerant piping...................................................................................................................

8.3.2

Precautions when checking the refrigerant piping ...............................................................................................

8.3.3

To check for leaks...................................................................................................................................................

8.3.4

To perform vacuum drying ....................................................................................................................................

8.3.5

To insulate the refrigerant piping ..........................................................................................................................

8.4

Charging refrigerant ...............................................................................................................................................................

8.4.1

About charging refrigerant ....................................................................................................................................

8.4.2

Precautions when charging refrigerant .................................................................................................................

8.4.3

To determine the additional refrigerant amount..................................................................................................

8.4.4

To determine the complete recharge amount......................................................................................................

8.4.5

To charge additional refrigerant ............................................................................................................................

8.4.6

To fix the fluorinated greenhouse gases label.......................................................................................................

8.5

Preparing water piping ...........................................................................................................................................................

8.5.1

Water circuit requirements ...................................................................................................................................

8.5.2

Formula to calculate the expansion vessel pre-pressure......................................................................................

8.5.3

To check the water volume and flow rate............................................................................................................. 100

8.5.4

Changing the pre-pressure of the expansion vessel ............................................................................................. 102

8.5.5

To check the water volume: Examples .................................................................................................................. 103

8.6

Connecting water piping ........................................................................................................................................................ 103
8.6.1

About connecting the water piping ....................................................................................................................... 103

8.6.2

Precautions when connecting the water piping.................................................................................................... 103

8.6.3

Connecting the water piping of the indoor unit.................................................................................................... 104

8.6.4

Connecting the water piping of the gas boiler ...................................................................................................... 105

8.6.5

To fill the space heating circuit .............................................................................................................................. 106

8.6.6

To fill the domestic water circuit of the gas boiler................................................................................................ 107

8.6.7

To fill the domestic hot water tank........................................................................................................................ 107

8.6.8

To insulate the water piping .................................................................................................................................. 107

8.7

Connecting the gas piping ...................................................................................................................................................... 108
8.7.1

To connect the gas pipe ......................................................................................................................................... 108

8.7.2

To perform an air purge on the gas supply ........................................................................................................... 108

8.1 Preparing refrigerant piping

8.1.1 Refrigerant piping requirements

INFORMATION

Also read the precautions and requirements in the

"3 General safety

precautions"

[

12].

Summary of Contents for Altherma EHYHBH05A Series








































































































































































































































































Search results

Summary of Contents for Altherma EHYHBH05A Series

Reviews:

Related manuals for Altherma EHYHBH05A Series

Brands by name

Popular brands

Daikin Altherma EHYHBH05A Series, Installer'S Reference Manual

Search results

Summary of Contents for Altherma EHYHBH05A Series

Reviews:

Related manuals for Altherma EHYHBH05A Series

Brands by name

Popular brands