manualshive.com logo in svg

Daikin Altherma EHYHBH05A Series, Installer'S Reference Manual

Share
Download
Daikin Altherma EHYHBH05A Series Installer'S Reference Manual Download Page 110

9

 | 

Electrical installation

Installer reference guide

110

08CA + EHY EHYHBH/X08A + EHYKOMB33AA

Daikin Altherma hybrid heat pump

4P355634-1G – 2022.09

9 Electrical installation

In this chapter

9.1

About connecting the electrical wiring .................................................................................................................................. 110
9.1.1

Precautions when connecting the electrical wiring .............................................................................................. 111

9.1.2

Guidelines when connecting the electrical wiring ................................................................................................ 111

9.1.3

Overview of electrical connections except external actuators............................................................................. 113

9.1.4

Overview of electrical connections for external and internal actuators .............................................................. 114

9.1.5

About preferential kWh rate power supply........................................................................................................... 115

9.2

Connections to the outdoor unit............................................................................................................................................ 116
9.2.1

To connect the electrical wiring to the outdoor unit ............................................................................................ 116

9.3

Connections to the indoor unit .............................................................................................................................................. 117
9.3.1

To connect the electrical wiring to the indoor unit............................................................................................... 117

9.3.2

To connect the main power supply of the indoor unit ......................................................................................... 118

9.3.3

To connect the main power supply of the gas boiler............................................................................................ 120

9.3.4

To connect the communication cable between gas boiler and indoor unit......................................................... 120

9.3.5

To connect the user interface................................................................................................................................ 122

9.3.6

To connect the shut-off valve ................................................................................................................................ 124

9.3.7

To connect the electrical meter............................................................................................................................. 125

9.3.8

To connect the gas meter ...................................................................................................................................... 125

9.3.9

To connect the domestic hot water pump............................................................................................................ 125

9.3.10

To connect the alarm output ................................................................................................................................. 126

9.3.11

To connect the space cooling/heating ON/OFF output ........................................................................................ 126

9.3.12

To connect the power consumption digital inputs ............................................................................................... 127

9.3.13

To connect the safety thermostat (normally closed contact)............................................................................... 127

9.1 About connecting the electrical wiring

Before connecting the electrical wiring

Make sure:

▪

The refrigerant piping is connected and checked

▪

The water piping is connected

Typical workflow

Connecting the electrical wiring typically consists of the following stages:

1

Making  sure  the  power  supply  system  complies  with  the  electrical
specifications of the heat pump.

2

Connecting the electrical wiring to the outdoor unit.

3

Connecting the electrical wiring to the indoor unit.

4

Connecting the main power supply of the indoor unit.

5

Connecting the main power supply of the gas boiler.

6

Connecting  the  communication  cable  between  the  gas  boiler  and  the  indoor
unit.

7

Connecting the user interface.

8

Connecting the shut–off valves.

9

Connecting the electrical meters.

10

Connecting the gas meter.

11

Connecting the domestic hot water pump.

12

Connecting the alarm output.

13

Connecting the space cooling/heating ON/OFF output.

14

Connecting the power consumption digital inputs.

15

Connecting the safety thermostat.

Summary of Contents for Altherma EHYHBH05A Series









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands