Daikin Altherma EHY2KOMB28AA Installer'S Reference Manual Download Page 44

Page: 44 / 112

9 Installation

Installer reference guide

EJHA EHY32AA

Daikin Altherma Hybrid hydrosplit heat pump

4P531180-1 – 2018.06

M2P

X2M

1×

3×

Fix the cable with cable ties to the cable tie mountings.

To connect the main power supply of the gas
boiler

Connect the power supply cable of the gas boiler to a fuse (a)
(L: X2-2 (BRN), N: X2-4 (BLU)).

Connect the earthing of the gas boiler to an earthing terminal.

Result:

The gas boiler performs a test. appears on the service

display. After the test, appears on the service display (wait mode).
The pressure in bar is shown on the main display.

DANGER: RISK OF ELECTROCUTION

A fused spur or an unswitched socket MUST be located no
more than 1 m from the appliance.

CAUTION

For installation in damp rooms, a fixed connection is
obligatory. When working on the electrical circuit ALWAYS
isolate the electric supply.

To connect the electrical wiring to the gas boiler

Open the gas boiler.

Open the switch box cover of the gas boiler.

Enter the wiring through the bottom of the unit.

a b

d e

Part

Description

Low voltage

Interconnection
cable between
outdoor unit and gas
boiler (current loop
PCB)

(*)

Factory-mounted
cable gland

Domestic hot water
tank thermistor

Knockout hole

Room thermostat or
heat pump
convector

Rubber grommet

High voltage

Power supply

Factory-mounted
cable gland

e + f

3‑way valve

Knockout hole

(*)

For more information on the current loop installation, read
the manual in the accessory bag of the current loop.

If needed, remove the knock-out holes with a screwdriver and
attach the field supplied glands.

Connect the wiring to the appropriate terminals. See

"17.2.2 Wiring diagram: Gas boiler" on page 99

Close the switch box cover of the gas boiler.

Close the gas boiler.

9.7.5

In case of third-party gas boiler

To connect the electrical wiring on the outdoor
unit

NOTICE

The distance between the high voltage and low voltage
cables should be at least 50 mm.

CAUTION

Do NOT push or place redundant cable length in the unit.

Open the top plate and the front plate. See

"9.2.2 To open the

outdoor unit" on page 30

Strip insulation (20 mm) from the wires.

Summary of Contents for Altherma EHY2KOMB28AA
















































































































Search results

Summary of Contents for Altherma EHY2KOMB28AA

Reviews:

Related manuals for Altherma EHY2KOMB28AA

Brands by name

Popular brands

Daikin Altherma EHY2KOMB28AA, Installer'S Reference Manual

Search results

Summary of Contents for Altherma EHY2KOMB28AA

Reviews:

Related manuals for Altherma EHY2KOMB28AA

Brands by name

Popular brands