Daikin (A)5LLF Service Manual Download Page 33

Page: 33 / 51

Required Tools

Si50-203

Semi-Hermetic Single Screw Compressor Version III

8. Required Tools

1. General Tools and Measuring Instruments

Table 8-1

List of general tools and measuring instruments

Table 8-2.

Tightening torque values for bolts (N - m)

Notes:

1. Indicate metric coarse threads and standard bolts (5T, 12.9).
2. Tolerances on tightening torque are ±15%.
3. When tightening hexagon socket head cap screws in the compressor, apply specifications

for class 12.9.

2. Special Tools

For an overhaul, be sure to prepare jigs listed in Table 8-3.

Table 8-3.

List of special tools

Name

Specification (size)

Application

Tool

Hex-key wrenches

M5, M6, M8, M10, M12, M16

Torque wrench

Refer table 8-2

C-type retainer ring
removing tools

For holes (large, small) and shafts

Gate rotor and bearing holders

Guide bolts

M6, M8, M10, M12, M16

Fixing plate and cover installation

Other general tools

Adjustable end wrench, spanners, pliers,
screwdrivers, hammer, plastic hammer, T-shape
wrenches, chisel

eas

uri

ins

tru

nts

Megger taster

500-V megger

Depth gauge

Dial type (minimum scale division: 0.01 mm)

Screw shims (1)

Thickness gauges

0.03 to 0.10 mm

Clearance between main bearing holder
and screw and slit clearance

Dial gauge

Minimum scale division: 0.01 mm, stroke: 10 mm For measuring Backlash

Nominal screw size

Class 12.9

3.0

11.6

5.2

14.0

12.3

34.0

M10

25.2

68.0

M12

42.7

118

M16

103

293

M20

202

570

M24

348

—

Name used in manual

Tool name

Application

Applicable model

Jig(1)

Lock nut tightening jig

Motor rotor mounting

ZH3~9F, G

Jig(2)

Jig(2)-1

Bearing removing jig

Removal of suction end cover

ZH3, 5F

Jig(2)-2

ZH3~9F, G

Jig(3)

Temporary bearing holder

mounting plate

Centering of screw

ZH3~9F, G

Jig(4)

Jig(4)-1

Handle

Adjustment of slit

ZH3, 5F

Jig(4)-2

ZH3~9F, G

Jig(5)

Oil filter removing jig

Required only for ZH3F

ZH3F

Summary of Contents for (A)5LLF




















































Search results

Summary of Contents for (A)5LLF

Reviews:

Related manuals for (A)5LLF

Brands by name

Popular brands

Daikin (A)5LLF, Service Manual

Search results

Summary of Contents for (A)5LLF

Reviews:

Related manuals for (A)5LLF

Brands by name

Popular brands