Dahua VTH1500B-S User Manual Download Page 2

Important Safeguards and Warnings 

Please read the following safeguards and warnings carefully before using the product in order 

to avoid damages and losses. 

Note: 

 

Do not expose the device to lampblack, steam or dust. Otherwise it may cause fire or 

electric shock.   

 

Do  not  install  the  device  at  position  exposed  to  sunlight  or  in  high  temperature. 

Temperature rise in device may cause fire. 

 

Do not expose the device to humid environment. Otherwise it may cause fire.   

 

The  device  must  be  installed  on  solid  and  flat  surface  in  order  to  guarantee  safety 

under load and earthquake. Otherwise, it may cause device to fall off or turnover. 

 

Do not place the device on carpet or quilt. 

 

Do  not  block  air  vent  of  the  device  or  ventilation  around  the  device.  Otherwise, 

temperature in device will rise and may cause fire. 

 

Do not place any object on the device.   

 

Do not disassemble the device without professional instruction. 

 

 

Warning:

 

 

Please use battery properly to avoid fire, explosion and other dangers.   

 

Please replace used battery with battery of the same type.   

 

Do not use power line other than the one specified. Please use it properly. Otherwise, 

it may cause fire or electric shock.     

 

Special Announcement 

 

This manual is for reference only.   

 

All the designs and software here are subject to change without prior written notice.   

 

All  trademarks  and  registered  trademarks  are  the  properties  of  their  respective 

owners.   

 

If there is any uncertainty or controversy, please refer to the final explanation of us.   

 

 

 

Summary of Contents for VTH1500B-S



















Reviews: