Dahua Mobile DVR Series User Manual Download

Page: 45 / 172



Compression: System default setup is H.264.



Resolution: Please select from the dropdown list. System max supports 1080P.



Frame rate (FPS): The frame rate value may vary due to different device capabilities. Please

select from the dropdown list.



Bit rate (Kb/S): It is to set bit rate.



Window split: It is to set window split mode.



Save: Click the Save button to save current setup. If this function is disabled, you cannot

operate zero-channel encoding function at the WEB, the video is black or null even you

operate when the function is disabled. After you enabled this function, login the Web and you

can select zero-channel encoding mode at the right corner of the

interface

. Select a mode; you can view the local preview video.



Overlay: Click Overlay, the interface is shown as in Figure 4-18.

Figure 4-18



Masking: Right now, this function is null.



Time time/license/speed title: Select a channel to overlay title and drag the title to the

corresponding position. The overlay function can overlay title on the real-time monitor video

or the playback file. Click time title and then click Monitor, click Set button to drag the overlay

title to the corresponding position.

Note

Plate title can control the plate and alarm title at the same time.

Step 3 Click OK button.

4.4 Main Menu

Step 1 On the preview window, right click mouse, and the select main menu, system pops up

Summary of Contents for Mobile DVR Series













































































































































































Search results

Summary of Contents for Mobile DVR Series

Reviews:

Related manuals for Mobile DVR Series

Brands by name

Popular brands

Dahua Mobile DVR Series, User Manual

Search results

Summary of Contents for Mobile DVR Series

Reviews:

Related manuals for Mobile DVR Series

Brands by name

Popular brands