background image

IV 

 

Connect the Device (type-I structure) to the power socket with protective earthing. 

 

The appliance coupler is a disconnection device. Keep a convenient angle when using it. 

Precautions 

 

Pass the turnstile as soon as possible after authorization. The arms will be closed after a specified 
time. 

 

When multiple people are entering, the continuous authorization interval is ≥ 1 s. 

 

Pay attention to the indicator of the turnstile. If it is a green arrow, passing in this direction is 
allowed; if it is a red cross, passing is not allowed. 

 

The turnstile supports anti-trailing and anti-reverse intrusion functions. If you force your way in 
the passage, the turnstile will lock the arms, which might cause personal injury. 

 

The turnstile will not correctly recognize the authorized card if it is used with other cards. 

 

Keep the authorized card well to make sure it works properly. 

 

Do not move anything through the turnstile; otherwise, the turnstile will consider it unauthorized. 

 

If the turnstile is to be installed outdoors where water pooling is likely to occur, it must be installed 
on a 50 mm–150 mm (adjust according to the actual situation) cement base. The passage also 
should be elevated to the same height of the cement base. Apply silicon sealant to the gap 
between the cement base and the turnstile to keep out water and condensation.

Summary of Contents for DHI-ASG2900C


































Reviews:

Related manuals for DHI-ASG2900C