Dahua DH-TPC-PT8320B Quick Start Manual Download Page 4

 

 

iii 

Important Safeguards and Warnings  

Safety Measures  

1. Qualified Engineer Needed  

 

The installation engineer or maintenance engineer shall have corresponding CCTV system 

installation certificate or maintenance qualification certificate.  

 

The installation engineer or maintenance engineer shall have qualification certificate for work 

at height.  

 

The installation engineer or maintenance engineer shall have the basic knowledge and 

operation technique for low-voltage cable layout and low-voltage electronic cable connection. 

 

Please read the installation manual carefully and keep it well for future reference, 

 

We are not liable for any problems caused by unauthorized modifications or attempted repair.

 

 

2. Lifting Appliance Requirement  

 

Please select the proper thermal hybrid dome installation mode and use the lifting 

appliances at the safety environment. 

 

The lifting appliances shall have the enough capacity to reach the installation height. 

 

The lifting appliances shall have safe performance.  

 

 

The precaution measures include two types: Warning and Note. 

 

Warning

: It is to alert you there is an optional risk of death or series injury! 

 

Note

: It is to alert you there is an optional risk of damage or property loss! 

 

Warning 

1.  All installation and operation here should conform to your local electrical safety codes. We 

assume no liability or responsibility for all the fires or electrical shock caused by improper 

handling or installation.  

2.  Be sure to use all the accessories (such as power adapter) recommended by manufacturer. 

3.  Do not connect several thermal hybrid domes to one power adapter. It may result in 

overheat or fire if it exceeds the rated load.  

4.  Avoid aiming the lens at the strong radiation source directly (such as sun, laser, molten steel 

etc); in case it may cause unrecoverable damage to the thermal imaging detector. What

’s 

worse, it may cause severe damage to the detector.  

5.  Avoid oil stain and kinds of chemicals tarnishing and damaging the lens surface. 

6.  Store  the  device  in  a  cool  and  dry  place  where  there  is  ventilation  but  no  intense 

Summary of Contents for DH-TPC-PT8320B
















Reviews: