manualshive.com logo in svg

Dahua DH-IPC-PSD8802-A180, Operation Manual

Share
Download
Dahua DH-IPC-PSD8802-A180 Operation Manual Download Page 180

Step 4 

Click "Save" to complete setting. 

 

5.5.3

  Record Control 

It is to configure pack duration, pre-event record, disk full, record mode and record stream. 

Step 1 

Select "Setup > Storage > Record Control" and the system will display the interface of "Record Control", 

which is shown in Figure 5-93. 

Figure 5-93

 

Step 2 

It is to configure the parameters of record control, please refer to Table 5-48 for more details. 

Parameter 

Note 

Pack Duration 

It is the duration to pack each video file. 

Pre-event 
Record 

It is the time of pre-event record when alarm generates. When it inputs 5, 
then the system will store the video 5 seconds before alarm occurs into the 
record file. 

Note 

The system will store the pre-event record video data before recording into 
the  record  file  when  alarm  or  dynamic  detection  activates  record  and  the 
record is not enabled. 

Disk Full 

It is the record strategy when the disk is full. 
Stop: it will stop recording when the disk is full. 
Overwrite: It will overwrite the earliest video file by cycle when the disk is 
full. 

Summary of Contents for DH-IPC-PSD8802-A180








































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands