Dafra DNPB328 Operation Manual Download Page 1

DNPB328 Operation Manual 

 

  

 

 

 

 

PLEASE SPEND 5 MINUTES READING 

THESE INSTRUCTIONS BEFORE USING 

YOUR NEW RIVNUT TOOL. 

 

TRUST US, IT WILL SAVE YOU TIME AND 
INCONVENIENCE IN THE LONG RUN.

 

 

 

READ THIS MANUAL CAREFULLY BEFORE USING THE TOOL!

 

  

It is 

IMPORTANT 

to follow the safety instructions for adequate protection 

against injuries.

 

 
 

 
-  This tool should be used 

ONLY

 to set blind rivets within the 

TOOL’S CAPACITY

.  It 

MUST 

NOT

 be used for other purposes, such as hammer, etc. 

 
-  This tool should be always operated with compressed air supply within the air pressure 

range 0.5Mpa ~ 0.7Mpa. 

 

-  Always 

DISCONNECT

 the air supply from the tool before changing the tool parts, such as 

mandrel, etc. 

 

DO NOT

 use the tool in the environment described as below: 

 

  fuel and combustion air. 

  temperature rapidly rising. 

  humidity, rain, water, storm and thunder, lightning. 

 

 

-  When the tool is suspended by the operation hook during use, be sure the tool will not fall. 
 
-  When using the tool, always carry protective goggles, protective gloves, safety helmet, and 

other necessary protections.  It is highly recommended for safety reasons. 

 

-  Only use genuine spare parts for maintenance and repairs. 

 

-  All repair work must be carried out by skilled personnel, when in doubt, always return the 

tool to the distributor. 

 
 
 

 
 

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for DNPB328











Reviews: