background image

20

(TROUBLE 4)

The following visual conditions indicate a probable defective touch control circuit

1. Incomplete segments,

1) Segments missing.
2) Partical segments missing.
3) Digit flickering other than normal display slight flickering.
4) " :0" does not display when power is on.

2. A distinct change in the display are not on when they numbers is the

display.

3. One or more digits in the display are not on when they should be.

4. Display indicates a number different from one touched.

5. Specific numbers (for example 2 or 3) will not display when the panel is touched.

6. Display does not count down or up with time cooking or clock operation.

7. Oven is programmable and cooks normally but no display shows.

8. Display obviously jumps in time while counting down.

9. Display counts down noticeably too fast while cooking.

10. Display does not show the time of day when the STOP/CLEAR button is pushed. (in case of setting the present time)

11. Oven lamp and turntable motor do not stop although cooking is finished. Check if the RELAY 2 contacts close.

If they close, replace P.C.B assembly.

NOTE 

Before following the particular steps listed above in the troubleshooting guide for the failure of membrane key-
board, please check for the continuity of each wire-harness between the membrane keyboard and P.C.B.
assembly.

CONDITION

CHECK

Check each pad for

continuity of the membrane

keyboard for the following key-

board check procedure

Malfunction

of the control cir-

cuit board

RESULT

Normal

CAUSE

REMEDY

Replace the

control circuit

board

Malfunction

of the membrane

keyboard

Abnormal

Replace the

membrane

keyboard

Display does

not show

programming

at all, even if

keyboard is

touched.

Summary of Contents for KOR-8CBB5W



































Reviews: