background image

24

Does the fan motor when you shut the door and turn the timer?

YES

YES

NO
continuity

NO microwave
oscillation.

Check continuity
of filament of
magnetron.

Does the oven lamp light?
Does the turntable turn?

2)

Check continuity
of filament of
magnetron

Check continuity fil-
ament tap (3.3V) of high
voltage transformer.

Check the diode for 
continuity in the reverse
and normal directions.

*Do not operate when you check this continuity.

*After short the contacts of a relay, operate oven.

*Normal reading should be approx. 0

.

*Meter with 6V or higher voltage batteries
 should be used to check the normal 
 direction resistance of the diode.

NO GOOD

Poor
continuity

Check the isolation of
filament winding of high
voltage transformer

Faulty magnetron

GOOD

NO

Replace or repair
oven lamp,
turntable motor.

NO
continuity

NO
continuity

continuity
in the

reverse
direction

Replace
magnetorn

Check the relay
contact of slow
acting relay ass'y

NO
operate

Replace
slow acting
relay ass'y

Replace
high voltage
transformer

Replace
high voltage
diode.

Replace high voltage
transformer

Replace 
Magnetron

operate

Summary of Contents for KOG-3605































Reviews: