Door gap adjusting
In case top and bottom gap of both doors are not the same, take the following steps to adjust.
(gap beteen the top right edge of feezer door and top left of refrigerator door)
21
1
First unscrew and remove top hinge covers.
refer to page 16~17
2
Turn the hinge fastener counterclockwise
2~3 times just to loosen. (Do not remove
the fastener.)
Moving to the right
1) Loosen the left screw(2-2) enough. (Do not
remove the screw.)
2) Turn the right screw(2-1) clockwise, then hinge
and top of freezer door moves to the right.
3) Once the gap is adjusted, fasten the left
screw(2-2) tightly.
Moving to the left
1) Loosen the right screw(2-1) enough. (Do not
remove the screw.)
2) Turn the left screw(2-2) clockwise, then hinge
and top of freezer door moves to the left.
3) Once the gap is adjusted, fasten the right
screw(2-1) tightly.
Adjustment of freezer door
Moving to the right
1) Loosen the left screw(2-1) enough. (Do not
remove the screw.)
2) Turn the right screw(2-2) clockwise, then hinge
and top of freezer door moves to the right.
3) Once the gap is adjusted, fasten the left
screw(2-1) tightly.
Moving to the left
1) Loosen the right screw(2-2) enough. (Do not
remove the screw.)
2) Turn the left screw(2-1) clockwise, then hinge
and top of freezer door moves to the left.
3) Once the gap is adjusted, fasten the right
screw(2-2) tightly.
Adjustment of refrigerator door
#
1
Insert a screw driver (flat tip) into a groove of the right wheel (bottom of refrigerator) and
turn it clockwise until the door is balanced. (clockwise to raise refrigerator door ;
counterclockwise to lower)
Unless the refrigerator door is balanced by step 1, then follow the next steps.
2
Loosen 3 hinge bolts(2 on the left + 1 on the right) a little. (Do not unfasten them
completely.)
Insert a hexagonal wrench into the groove of adjusting nut and turn clockwise until the
door is level.
3
Once the door is balanced, fasten the hinge bolts tightly.
In case refrigerator door is lower than freezer door...
Hinge Bolt
After installation and/or door leveling, fasten front cover with screws.(Remove the screws on the front bottom panel first.
Click and screw the cover)
Front Cover
Refrigerator Leveling &
Door Adjustment ( If needed. )
Refrigerator must be level in order to maintain optimal performance and desirable front appearance.
(If the floor beneath the refrigerator is uneven, freezer and refrigerator doors look unbalanced.)
20
#
$
1
Insert a screw driver (flat tip) into a groove of the left wheel (bottom of freezer) and turn it
clockwise until the door is balanced. (clockwise to raise freezer door ; counterclockwise
to lower)
Unless the freezer door is balanced by step 1, then follow the next steps.
2
Open the doors, unscrew the front cover and remove, if it is attached.
3
Loosen 3 hinge bolts(1 on the left + 2 on the right) a little. (Do not unfasten them
completely.) Insert a hexagonal wrench into the groove of adjusting nut and turn
clockwise until the door is level.
4
Once the door is balanced, fasten the hinge bolts tightly and screw the front cover.
In case freezer door is lower than refrigerator door...
The front of refrigerator needs to be higher just a little than the back for easy door
closing, but if the wheel is raised too much for door balance, i.e. front of refrigerator
is too higher than the back, it can be difficult to open the door.
Hinge Bolt
