16
15
Proper care of your washer can extend its life. This section explains how to care for your washer
properly and safely.
Cleaning your washer
Winter storage or moving care
Install and store your washer where it will not freeze, because some water may stay in the
hoses, freezing can damage your washer.
If storing or moving your washer during freezing weather, winterize it.
Non-use or vacation care
Operate your washer only when you are at home.
If you will be on vacation or not using your washer for an extended period of time, you should:
• Unplug the power supply cord or turn off eletrical power to the washer.
• Turn off the water supply to the washer.
This helps avoid accidental flooding (due to a water pressure surge) while you are away.
PERIODIC MAINTENANCE
Wipe up detergent, bleach, and other spills
with a soft, damp cloth or sponge as they
occur. occasionally wipe the outside of the
washer to keep it looking like new.
Clean interior with 250ml of chlorine bleach
mixed with 500ml of detergent.
Run washer through a complete cycle.
Repeat process if necessary.
Exterior
Interior
• Shut off water faucet.
• Disconnect and drain water inlet hoses
• Run washer on a drain and spin setting
(see page 13) for 1 minute.
• Unplug the power supply cord.
• Flush water pipes and hoses.
• Reconnect water inlet hoses.
• Turn on water faucet.
• Reconnect power supply cord.
To winterize washer
To use washer again
Do not put sharp or metal object in your washer,
they can damage the finish. Check all pockets
for pins, clips, money, bolts, nuts, etc.
Do not lay these objects on your washer after
emptying pockets.
Delay wash cycle
!
Set your program as the
above procedure,
remaining last step.
* Press the cycle selection button.
* Press the procedure selection button.
* Wool cycle is not selectable with delay
wash cycle.
@
Press delay button until the
digital monitor displays the
delayed time you want.
#
Press Start/Hold to start.
DELAY
START
/ HOLD
For the partial process or the combinations, or for adding time of each process.
step 1. Press power switch.
step 2. Press program button until the indicating lamps make the combinations you want.
If only spin lamp is turned on, that means you will operate your washer for spin only.
If rinse and spin lamp are turned on, that means you will operate your washer for rinse and spin.
If add lamp is turned on with other program lamps, that means the time of the corresponding
program will increase by 1~2 minutes, that is, if add is on with wash, rinse and spin, the time of each
program will increase by 1~2 minutes. (Wash: add 2 min., Rinse: add 1 min., Spin: add 1 min.)
step 3. Press water level selector as your decision.
step 4. Press Start/Hold to start.
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
WASH
ADD
RINSE
SPIN
START
/ HOLD
PROGRAM
WASH
ADD
RINSE
SPIN
WATER
LEVEL
HIGH
MID
LOW
POWER
!
Pressing
@
Selecting
$
Pressing
the Power
Water level
#
Selecting Cycle
the Start/
Switch
Hold Switch
Wash & Rinse
& Spin
Only Spin
Add & Wash
Add & Rinse
& Spin
Add & Spin
Add & Wash
& Rinse & Spin
Only Wash
Rinse & Spin
End of
Washing
It is
confirmed
by buzzer.
,
,
,
GUIDES FOR OTHER USEFUL PROGRAMS