background image

3

Save these instructions

Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the
following basic precautions.

Understanding your responsibilities

• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same

wash. Hazardous fumes can form.

• Unplug power supply cord before attempting to service your washer.
• Do not wash fiberglass material.

Small particles can stick to fabrics washed in following loads and cause skin irritation.

• Do not spray water on the control panel of the washer.

It could cause fire or an electric shock.

• In case of the dual valve model, if you connect only one water inlet valve, the water leakage

from other water inlet valve(unconnected) can occurs.

• This appliance must be grounded. 

To avoid electrical shock, use a metal pipe for the ground connection.

• Flammable fluids (dry-cleaning solvents,

kerosene, gasoline, etc.) should not be used
or stored in or near your washer.
Do not add flammable fluids to your wash
water.These substances give off vapors that
can create a fire hazard or explosion.

• After starting a cycle, do not reach into the

washer until all motions stop.

• Do not tamper with the controls.
• The appliance is not intended for use by

young children or infirm persons without
supervision.

• If the supply cord is damaged, it must be

replaced by the manufacturer, or its service
agent or a similarly qualified person in order
to avoid a hazard.

• If the appliance is supplied from a cord

extension set or electrical portable outlet
device it should be positioned so that it is not
subjected to splashing or ingress of
moisture.

Please ...
• Have only a qualified person install, repair, 

or replace parts on washer.

• Maintain washer properly.
• Protect washer from the weather and keep

it where the temperature will not fall below
freezing.

• Do not install the washer at a place of

extremely high humidity. It could cause an
electric shock or a short circuit.

• Connect washer to the correct outlet,

electrical supply, water supply, and drain
supply.

WASHER SAFETY

Read all instructions before using your washer

Summary of Contents for DWD-M8021


















Reviews: