background image

A. Caution on Installtion

• Install the washer in the place easy access to water, electrical power and drainage.
• Install the washer on a firm, and flat floor.
• Connect the grounding wire to a water faucet if the pipe is made of metal before plugging the power cord into the

socket.

• Avoid installing the machine where it can be exposed to rain or direct ray of the sun, that may cause a trouble or

discoloration. In case the machine has to be installed in such a place, provide a shield to protect machine from rain or
direct rays of the sun.

• Be sure that inside of panel are enough tightened to prevent water leakage.
• In summer or other periods when there is a great difference between the water temperature and the air temperature,

drops of water may condense on the outside of the tub, and the floor might become wet from dripping; be careful of
this. 

• Please disconnect the power cord plug after washing.

B. Grounding

• Connect the grounding wire to a water faucet if the pipe is made of metal before plugging the power cord into the

socket.

• Make sure that the power cord is unplugged during ground work.

• Be sure to wind grounding wire on the metal pipe like Fig 1. (Do not

connect the grounding wire end to a gas tube). 

• For maximum security, attatch the grounding wire to a copper plate or

grounding rod and bury it at least 20cm in the ground like Fig. 2. 

C. Caution on Use

• Do not use water which contains rust.
• Never put your hands into the tub through wash and rinse process.
• Do not allow water to contact the switches in the control panel. 
• Drain the water in the wash tub fitting selector switch on the drain position.
• Use only water above 0°C

CAUTION ON USE

CAUTION ON THE OPERATION

Grounding Wire

More than 20cm 

Grounding Rod 

Fig. 1

Fig. 2

3

Putting in the clothes
distribute the clothes in the
tub being sure that nothing is
protruding out of the top. 

Pocket Check
Check the pockets of the
laundry and remove contents
that shouldn't be washed
before putting the laundry into
the tub. 

Detergent Amount
If you use too much detergent,
excessive amount of suds and
rinsing may be arisen: limit the
amount of detergent you use. 

Acting time of pulsator

Wash Action

Move Stop.

Normal Reverse

30"

4"

Soft Reverse

4.5"

6.8"

Summary of Contents for DW-3600






















Reviews: