background image

15

KNOW YOUR LAWN MOWER

Read this manual carefully, observing the recommended safety instructions before, during and after 
using your lawn mower. Following these simple instructions will also maintain your lawn mower in 
good working order. Familiarize yourself with the controls on your mower before attempting to 
operate it, but above all, be sure you know how to stop your mower in an emergency. Retain this 
user manual and all other literature with your mower for future reference.

1. SYMBOLS MARKED ON THE PRODUCT

 

 

Read this instruction book carefully before using the lawn mower and keep it 

 

 

in a safe place for future reference.

 

 

Keep bystanders away.

 

 

Beware of sharp blades. Blades continue to rotate after the motor is switched off.

 

 

Switch off isolator key before adjusting, cleaning and before leaving the product 

 

 

unattended for any period.

 
 

 

The charger is intended for indoor use only.

 

 

Wear hearing and eye protection.

 

 

The machine is protected against ingress of water drop from vertical direction.

 

 

Do not expose to rain or damp conditions.

 

 

Do not operate on inclines greater than 15°.Mow across the face of slopes,

 

 

never up and down.

 

 

Electric shock hazard.

 

 

Wait until all machine components have completely stopped before touching them.

  
  CE 

Marking

 

 

The product meets demands and regulations set by the European Community.

  WEEE 

Marking 

 

 

CAUTION! Unusable power tools do not belong with domestic waste. 

 

 

They must be taken to a communal collecting point for environmentally friendly 

 

 

disposal in accordance with local regulations.

Accumulator Disposal:

Old Accumulators and batteries must not be added to household waste, but should be disposed of 
in accordance with the applicable legislation.
Take unusable rechargeable batteries to the dealer’s or community’s battery collection point. 

Disposing of the packaging:

The packaging is made of cardboard and separately labeled foil which is also recyclable. 
Take these materials to a recycling centre. 

Disposing of the packaging:

The packaging is made of cardboard and separately labeled foil which is also recyclable. 
- Take these materials to a recycling centre. 

Battery packs/batteries:

  Li-lon
 

 

Do not dispose of batteries into household waste, water or fire. Battery packs/

 

 

batteries must be collected, recycled or disposed of in an environmentally 

  -friendly 

way.

Only for EC countries:

Defective or dead batteries must be recycled according to the directive 2006/66/EC.

 

 

Noise level marking for model DLM4340Li

 

 

Your tool noise is not more than 92dB.

 

SAFETY ALERT SYMBOL:

 Indicates caution or warning may be used in conjunction with 

other symbols or pictures.

2. GENERAL SAFETY RULES

The purpose of the safety rules is to attract your attention to possible dangers. The safety symbols 
and the explanations with them, require your careful attention and understanding. The safety war-
nings do not by themselves eliminate any danger. The instruction or warnings they give are not 
substitutes for proper accident prevention measures.
 WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. 
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. 
Save owners manual and review frequently for continuing safe operation and instructing others who 
may use this tool.

 

WARNING:

 This machine produces an electromagnetic field during operation. This field may 

under some circumstances interfere with active or passive medical implants. To reduce the risk of 
serious or fatal injury, we recommend persons with medical implants to consult their physician and 

the medical implant manufacturer before operating this machine.

 

WARNING:

 The operation of any tool can result in foreign objects being thrown into your 

eyes, which can result in eyes severely damaged. Before beginning power tool operation, always 
wears safety goggles or safety glasses with side shields and a full face shield when needed. We 
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side 
shield.

IMPORTANT

READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE.

1) Read the instructions carefully. Be familiar with the controls and the proper use of the equipment.
2) Never allow children or people unfamiliar with these instructions to use the lawnmower. Local 
regulations can restrict the age of the operator.
3) Never mow while people, especially children, or pets are nearby.
4) Keep in mind that the operator or user is responsible for accidents or hazards occurring to other 
people or their property.
5) While mowing, always wear substantial footwear and long trousers. Do not operate the equip-
ment when barefoot or wearing open sandals; Avoid wearing clothing that is loose fitting or that has 
hanging cords or ties.
6) Thoroughly inspect the area where the equipment is to be used and remove all objects which can 
be thrown by the machine.
7) Before using, always visually inspect to see that the blades, blade bolts and cutter assembly are 
not worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance. 
Replace damaged or unreadable labels.
9) mow only in daylight or in good artificial light.
10) avoid operating the equipment in wet grass, where feasible.
11) Always be sure of your footing on slopes.
12) Walk, never run.
13) For wheeled rotary machines; mow across the face of slopes, never up and down.
14) exercise extreme caution when changing direction on slopes.
15) Do not mow excessively steep slopes.
16) Use extreme caution when reversing or pulling the lawnmower towards you.
17) Stop the blades if the lawn mower has to be tilted for transportation when crossing surfaces 
other than grass, and when transporting the lawn mower to and from the area to be mowed.
18) Never operate the lawnmower with defective guards, or without safety devices, for example 
deflectors and/or grass catchers, in place.
19) Start or switch on the motor carefully according to instructions and with feet well away from the 
blades.
20) Do not tilt the lawnmower when starting switching on the motor, except if the lawnmower has to 
be tilted for starting. In this case, do not tile it more than absolutely necessary and lift only the part 
which is away from the operator.
21) Do not start the motor when standing in front of the discharge chute.
22) Do not put hands or feet near or under rotating parts, Keep clear of the discharge opening at all 
times.
23) Never pick up or carry a lawnmower while the motor is running.
24) Stop the motor and switch off isolator key. Make sure that all moving parts have come to a 
complete stop :
 

- Whenever you leave the machine;

 

- Before clearing blockages or unclogging chute;

 

- Before checking, cleaning or working on the lawnmower;

 

- After striking a foreign abject. Inspect the lawnmower for damage and make repairs before

 

restarting and operating the lawnmower.

 

If lawnmower starts to vibrate abnormally (check immediately) :

 

- Inspect for damage;

 

- Replace or repair any damage parts;

 

- Check for and tighten any loose parts.

25) Stop the mower:
 

- Whenever you leave the lawnmower.

26) keep all nuts, blots and screws tight to be sure the equipment is in safe working condition.
27) check the grass catcher frequently for wear or deterioration.
28) Replace worn or damaged parts for safety.
29) Children are not allowed to use the machine.
30) This appliance is not intended for use by persons with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, unless they have been given supervision or 
instruction concerning use of the appliance by a person responsible for their safety.
31) Be careful during adjustment of the machine to prevent entrapment of the fingers between 
moving blades and fixed parts of the machine.
32) Always allow the machine to cool before storing.
33) After use and before storage, remove the battery from the machine and check for damage.
34) When servicing the blades be aware that, even though the power source is switched off, the 
blades can still be moved.
35) Replace worn or damaged parts for safety; Use only genuine replacement parts and acces-
sories.
36

Be careful during adjustment of the appliance to prevent entrapment of the fingers between 

moving blades and fixed parts of appliance.
37

Recharge only with the charger specified by the manufacture .Using a charge with an incompati-

ble battery pack may create a risk of fire.
38

Use power tools only with specifically designated battery packs .Use of any other battery packs 

may create a risk of injury and fire.
39

When battery pack is not in use ,keep it away from other metal objects like ,paper clips ,coin, 

keys, nails, screws ,or other small metal objects, that can make a connection from one terminal to 
another. Shorting the battery terminals together may cause burns or a fire.
40

Under abusive conditions, liquid may be ejected from the battery: 

 

- If contact accidentally occurs, flush with water;

 

- If liquid contacts eyes additionally seek medical help. Liquid ejected from the battery may  

 

cause irritation or burns.

1. When device is not in use, keep it away from other metal objects like paper clips, coins, keys, 
nails, screws, or other small metal objects that can make a connection from one terminal to another. 
Shorting the battery terminals together may cause burns or a fire.
2. Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid 
ejected from the battery may cause skin irritation or burns.

Safety Advice for Rechargeable Battery and Charger

Use only the battery provided with the lawn mower and the provided charger. 
Protect battery and battery charger from humidity. 
Do not operate the battery charger outdoors. 

When it is not in use or before cleaning and servicing, disconnect the battery charger from the 
power supply. 
Take special care of the battery. 
Avoid dropping it onto any hard surface and do not subject it to pressure or any other form of 
mechanical stress. 
Keep the battery away from extreme heat and cold.
Do not open or attempt to repair the battery or the battery charger. If any parts are defective, have 
them repaired by a qualified technician or send them to our service department for repair. 
Only charge the battery at an ambient (surrounding air) temperature between 0ºC and +50ºC. 
A charged battery can be used to power the machine under ambient temperature conditions 
between -20ºC and +70ºC. 
When not in use, store the battery in a dry place between 10ºC and 30ºC.

The battery should be recharged when it fails to produce sufficient power on jobs which were 
easily done previously. 

DO NOT CONTINUE using product with its battery in a depleted condition.

The battery is not fully charged at the factory. 

Before attempting to use it, it must be fully charged 

firstly.
 
 

IMPORTANT! DANGER! 

Never short-circuit the battery or expose it to moisture. Do not store it together with any metal parts 
which could short-circuit the contacts. The battery could overheat, start burning or explode.
If any person comes into contact with acid or similar internal fluids or substances contained in the 
battery, wash off these substances immediately with plenty of water. If these substances make 
contact with the eyes, rinse with plenty of water and visit a doctor immediately.

 

WARNING!

Do not open the battery pack to get the battery out by yourself. 
Do not place the rechargeable battery into fire or water. It can explode. The Rechargeable Battery 
should not be discarded to domestic refuse, regardless of whether used or unused. You should 
return it to a local battery collection point in accordance with Battery Regulations or return them to 
us suitably marked “Used Battery”.

3. GENERAL IDENTIFICATION

1. On-off button  
2.Lock off button
3. Switch box
4. Locking knob
5. Grass catcher 
6. Cable clamp
7. Height adjustment lever
8. Wheel 
9. Deck 
10. Battery door 
11. Lower handle         
12. Upper handle                       
13. Mulching wedge 

4. TECHNICAL DATA

Model DLM4340Li                                 
Rated Voltage: 40V d.c.
Rated Power: 550W
No Load Speed: 3100 rpm
Grass catcher capacity: 50L
Cutting Width: 410 mm
Net weight: 21.4kg
Height adjustment: 25-75 mm, 7 adjustment

Model DYM1072
Sound Pressure level at the operator’s position: 79.9dB(A) K=3 dB(A)
Measured Sound power level: 90.1dB(A) K=2.07dB(A)
Guaranteed Sound Power level: 92dB(A)
Vibration: Max.1.29m/s² K=1.5 m/s²

Battery   Lithium-ion
Model number 

DYMA81 

DYMA72E

Rated voltage 40V d.c. 

40V d.c.

Capacity 

 90Wh 

 144Wh

Number of battery  20pcs   

20pcs

Battery charger 
Model number 

DYMA83

Input: 220-240VAC,50Hz,1A
Output: 40V d.c.,2A
Allowable charging temperature range 

0-50ºC

5. ASSEMBLY

5.1 Assemble the folding handle

A).Fix the lower handlebars into the unit body with locking knobs, bolts and washers.
(Fig. 2A/ Fig. 2B/ Fig. 2C).
B) Release the upper handlebars for folding. Connect the upper handle and the lower handle with 
locking knobs, bolts and washers. (Fig. 2D/ Fig. 2E/ Fig. 2F).
C).Attach the cable clamp to the position shown and then attaches the cable. (Fig. 2G/ Fig. 2H).

5.2 Assemble the grass catcher

Assembly the handle into the grass catcher (Fig. 3A/ Fig. 3B/ Fig. 3C)
Insert one end with a projection into the grass catcher, and then fixed another end of the handle 
onto the grass catcher with the screw.
1. To fit: Raise the rear cover and hitch the grass catcher on rear of mower. (Fig. 3D/ Fig. 3E/ Fig. 3F)
2. To remove: Grasp and lift the rear cover, remove grass catcher.
There is a level indicator on the top of the grass catcher that shows whether the catcher is empty or 
full:
 

- The level indicator inflates if the catcher is not full during the moving. (Fig. 3G)

 

- If the catcher is full, the indicator collapses; once this happens stop moving immediately 

 

and empties the catcher, make sure it is clean and ensure its meshwork is ventilated. 

 

(Fig. 3H).

 
 

IMPORTANT:

If the position of indicator opening is very dirty, the indicator will not inflate-in this case, clean the 
position of indicator opening immediately.

5.3 Assemble the isolator key

1. Press the button (1) and lift the battery door.(2) (Fig. 4A/ Fig. 4B)
2.Insert the isolator key into the slot. (Fig. 4C).

5.4 Assemble the battery

1. Open the battery door.
2. Make sure the isolator key is switched off. Switch mark ”1” is ON”, “0” is “OFF”. (Fig. 5A)
3. Insert the battery pack into battery holder, one or two battery is both workable. (Fig. 5B)
4. Make sure the latch on bottom of battery pack snaps in place and that battery pack is fully 
seated. (Fig. 5C).
5. Close the battery door. (Fig. 5D).

5.5 Remove the battery (Fig. 6A/ Fig. 6B)

1. Lift and hold up the battery door
2. Press and hold the battery latch button (1) at the bottom of the battery pack.
3. Remove battery pack (2) from the product.

5.6 Adjustment for an appropriate the height

1. Back out the locking knobs which fixed the lower handle. (Fig. 7A/ Fig. 7B).
2. Refer to Fit.7C, move the lower handle up and down, adjust it to the proper height. There is 3 
adjusting height to be choose on this type lawn mower; at 1 height, lower handle to the ground is 
highest, 3 height is the lowest.
3. Adjusting to the proper height, then fix the lower handle by the locking knobs.

 

WARNING:

 The left side and right side of lower handle must adjust to the same height.

6. ADJUSTMENT OF CUTTING HEIGHT

Apply outward pressure to disengage lever from rack. Move lever forward or back to adjust height. 
The height (the blade to the ground) can be adjusted from 25mm to 75mm , 7 height positions. 
(Fig.8).

 

WARNING:

 Make this adjustment only when the blade is stopped.

 

WARNING:

 Disconnect the electric cord from the power supply.

7. “2 IN 1”

These lawn mowers can be retrofitted from its normal function, based on the application purpose:
From lawn mower with rear discharge to mulching mower 
What is mulching?
When mulching, the grass is cut in one working step, then finely chopped and returned to the grass 
strip as natural fertilizer.
Hints for mulch-mowing:
 

- Regular cut-back by max.2cm form 6cm to 4cm grass height.

 

- Use a sharp cutting knife - Do not mow wet grass 

 

- Set max. Motor speed

 

- Only move at working pace

 

- Regularly clean mulching wedge, housing inner side and mowing blade

Starting Operation 
ONE: Retrofitting for mulching mower 

 

WARNING:

 only with a stopped motor and standstill cutter.

1. Raise the rear cover and remove the grass catcher.
2.Push the mulching wedge into the deck. Lock the mulching wedge into the opening on the deck. 
(Fig. 9A/ Fig. 9B).
3. Lower the rear cover again. (Fig. 9C).

TWO: Mowing with the grass catcher

 

WARNING: 

only with a stopped motor and standstill cutter.

For mowing with the grass catcher, remove the mulching wedge and mount the grass catcher.
1. Removing the mulching wedge:
 

- Lift rear cover and remove the mulching wedge. 

2. Mount the grass catcher:
 

- To fit: Raise the rear cover and hitch the grass catcher on rear of mower. 

 

- To remove: Grasp and lift the rear cover, remove grass catcher.

 

WARNING: 

Disconnect the electric cord from the power supply.

8. SAFETY PRECAUTIONS

a) Always operate with the deflector or grass catcher in the correct position.
b) Always stop the motor before removing the grass catcher or adjusting the height of cutting posi-
tion.
c) Before mowing, remove all foreign objects from the lawn which may be thrown by the machine. 
While mowing, stay alert for any foreign objects which may have been missed.

Fig.10A

d) Never lift the rear of the mower while starting the motor or during normal operation.

Fig.10B

e) Never place your hands or feel underneath the under pan or into the rear discharge chute while 
the motor is running. (Fig. 10C).

9. OPERATING INSTRUCTIONS 

9.1. Starting

Switch on the isolator key. 
Start the motor as follows( Fig.11):
a) Press the safety push-button (1).
b) And meanwhile, press any switch button (2) (There are four buttons) , and keep it in grasp.
Lift the front of the machine and switch off isolator key while crossing gravel or roads surface.
If you release the switch button, the motor will stop.

 

CAUTION! 

The blade starts turning as soon as the motor is started.

 

WARNING!

 Cutting elements continue to rotate after the motor is switched off.

 

CAUTION! 

 your mower is designed to cut normal residential grass of a height no more than

 250mm. 
 

Do not attempt to mow through unusually tall dry or wet grass (e.g. pasture) 

 

or piles of dry leaves. 

9.3 LED

Please refer to the following table for the meaning of LED display. (Fig. 13A/ Fig. 13B).

9.4 For the best results when mowing

Clear lawn of debris. Be sure that the lawn is clear of stones, sticks, wire or other foreign objects 
which could be accidentally thrown out by the mower in any direction and cause serious personal 
injury to the operator and others as well as damage to property and surrounding objects. Do not cut 
wet grass. For effective mowing do not cut wet grass because it tends to stick to the underside of 
the deck preventing proper mowing of the grass clippings. Cut no more than 1/3 the length of the 
grass. The recommended cut for mowing is 1/3 the length of the grass. Ground speed will need to 
be adjusted so the clippings can be dispersed evenly into the lawn. For especially heavy cutting in 
thick grass it may be necessary to use one of the slowest speeds in order to get a clean well mowed 

Fig. 14

cut. When mowing long grass you may have to cut the lawn in two passes, lowering the blade ano-
ther 1/3 of the length for the second cut and perhaps cutting in a different pattern than was used the 
first time. Overlapping the cut a little on each pass will also help to clean up any stray clippings left 
on the lawn. The mower should always be operated at full throttle to get the best cut and allow it to 
do the most effective job of mowing. Clean underside of deck. Be certain to clean the underside of 
the cutting deck after each use to avoid a build-up of grass, which would prevent proper mulching. 
Mowing leaves. The mowing of leaves can also be beneficial to your lawn. When mowing leaves 
make sure they are dry and are not laying too thick on the lawn. Do not wait for all the leaves to be 
off the trees before you mow.

 

WARNING: 

if you strike a foreign object, stop the motor. Switch off the isolator key, thorou-

ghly inspect the mower for any damage and repair the damage before restarting and operating the 
mower. Extensive vibration of the mower during operation is an indication of damage. The unit 
should be promptly inspected and repaired.

10. BLADE

The blade is made of pressed steel. It will be necessary to reshape it frequently (with a grind wheel).
Ensure that it is always balanced (an unbalanced blade will cause dangerous vibrations). To check 
for balance, insert a round rod through the central hole and support the blade horizontally. A balan-
ce blade will remain horizontal. If the blade is not balanced the heavy end will rotate downwards. 
Reshape the heavy end until the blade is currently balanced. To remove the blade (1), unscrew the 
blade screw (2).
and replace any parts, which are damaged.
When reassembling, make sure that the cutting edges face in the direction of the motor rotation. 
The blade screw (2) must be torque to 20N.m.

 

WARNING:

 For service, replace the blade with DAYE blade: DAYE 263003498 

 

WARNING:

 Remove the battery from the machine.

 

WARNING:

 Protect hands by using heavy gloves or a rag to grasp the cutting blades  

 

 

when replace the blade. 

11. MAINTENANCE AND CARE

 

WARNING:

 Before performing any Maintenance or cleaning work, Always remove batterys 

and switch off the isolator key! 
Do not spray the unit with water. Ingress of water may destroy the switch and the electric motor. 
Clean the unit with a cloth, hand brush, etc. 

Expert inspection is required, do not make any adjustment by yourself, must contact to custo-
mer Service centre: 

a) if the lawn mower strikes an object. 
b) if the motor stops suddenly 
c) if the blade is bent (do not align!)                 
d) if the motor shaft is bent (do not align!)
e) if a short-circuit occurs when the cable is connected. 
f) If the V-belt is defective. 
h) Use only manufacturer’s recommended replacement parts and accessories.

12. TROUBLESHOOTING 

 

WARNING:

before performing any maintenance or cleaning work, always remove batteries 

and switch off the isolator key! Only with a stopped motor and standstill cutter.

 

CAUTION!

 Faults which can not be rectified with the aid of this table may be rectified by a 

specialist company only (customer service centre).

13. ENVIRONMENTALLY FRIENDLY DISPOSAL

According to EU directive 2012/19/EU on electric and electronic equipment and its implementation 
into national law, all electric tools must be separately collected and environmentally friendly recy-
cled. Alternative disposal: If the owner of the power tool does not return the tool to the manufactu-
rer, he is responsible for proper disposal at a designated collection point that prepares the device 
for recycling according to national recycling laws and regulations.
This does not include accessories and tools without electric or electronic components.

Summary of Contents for DLM4340Li







































Reviews: