background image

12

11. POSSIBLE PROBLEM AND SOLUTION

9. ATTACHING SOAP DISPENSER BOTTLE

Insert metal end of the spray lance into the opening of spray gun (making sure to match the locking 
tabs on either side of the spray lance to the notches of the spray gun), Push in and twist in a cloc-
kwise motion to lock spray lance and spray gun together (make sure there is a tight and secure 
fitting between both). Insert end of soap dispenser bottle with the plastic locking tabs into opening 
of the spray lance. Push in, turn, and lock so the soap dispenser bottle and spray lance are firmly 
secure.

10. CLEANING PIN INSTRUCTION

• Using included tip cleaner, or an unfolded paper clip, insert wire into the nozzle hole and move 
back and forth until debris is dislodged. 

• Remove additional debris by back-flushing water through the nozzle. To do this, place end of a 
garden hose (with water running ) to the end of nozzle for 30-60 seconds.

seconds racing of the motor to let take water completely spray out.
5. Disconnect the garden hose from the pressure washer.
6. Wipe all surfaces of the unit with a damp clean cloth.
7. Engage the gun safety lock.

CAUTION:

 ALWAYS turn off the unit’s motor BEFORE turning off the unit’s water supply.

Serious damage could occur to the motor if the unit is run without water. 

CAUTION: 

NEVER disconnect the high-pressure discharge hose from the machine while the system 

is still pressurized. To depressurize the unit, turn off the motor, turn off the water supply and 
squeeze the trigger 2-3 times.

6. ADJUSTABLE SPRAY NOZZLE

Turn off the spray lance first, and then adjust the nozzle. Water may be sprayed out from the spray 
nozzle either linearly (Fig 1) or in fan shapes (Fig 2).

7. WATER INLET SCREEN

The water inlet filter must be inspected regularly, so as to avoid blockage and restriction in the water 
supply to the pump (Fig 3).

8. GUN SAFETY DEVICE

When you stop the machine it is necessary to use the safety lock placed on the gun in order to 
avoid accidental.

WARNING:

 The electrical supply connection shall be made by a qualified person and comply with 

IEC 60364-1. The electric supply to this machine should include either a residual current device that 
will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms or a device that will 
prove the earth circuit.

WARNING:

 The machine is intended to be used at a temperature above o degree. (Only for machine 

with power cord of H05VV-F).
WARNING: The operating method to be followed in the event of accident (e.g. contact with deter-
gents: rinse with an abundance of clean water) or breakdown to prevent unsafe situations.

WARNING:

 This machine has been designed for use with the cleaning agent supplied or recommen-

ded by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the 
safety of the machine.

WARNING:

 Recommend the operator to wear ear protectors.

WARNING:

 Do not use the machine within range of persons unless they wear protective clothing.

WARNING:

 Do not direct the jet against yourself or others in order to clean clothes or foot-wear.

WARNING:

 Risk of explosion-Do not spray flammable liquids.

WARNING: High pressure hoses, fittings and couplings are important for the safety of the machine. 
Use only hosed, fittings and couplings recommended by the manufacturer.
WARNING: To ensure machine safety, use only original spare parts from the manufacturer or appro-
ved by the manufacturer.
WARNING: Water that has flown through backflow preventers is considered to the non-potable.

WARNING:

 The machine shall be disconnected from its power source by removing the plug from the 

socket-outlet during cleaning or maintenance and when replacing the machine to another function.

WARNING:

 Observe a distance of at least 30cm when using the jet to clean painted surfaces to 

avoid damaging paintwork.

WARNING:

 Do not use the machine if a supply cord or important parts of the machine are damaged, 

e.g. safety devices, high pressure hoses, trigger gun.

WARNING:

 If an extension cord is used, the plug and socket must be of watertight construction.

WARNING:

 Inadequate extension cords can be dangerous. If an extension cord is used, it shall be 

suitable for outdoor use, and the connection has to be kept dry and off the ground. It is recommen-
ded that this is accomplished by means of a cord reel which keeps the socket at least 60mm above 
the ground.

WARNING:

 In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this 

appliance must not be supplied through an external switching device, such as a timer, or connected 
to a circuit that is regularly switched on and off by the utility.

 

 

The machine is not intended to be connected to the potable water mains. 

  

WARNING:

 To ensure the machine safety, please only use original spare parts

 

 

(including nozzle) from the manufacturer or approved by the manufacturer. Do not use 

 

 

the machine before you changed them if they are damaged.

WARNING:

 Be care of the danger of the kickback force on the spray assembly when opening the 

trigger gun and grasp the gun with hands firmly.

WARNING:

 To reduce the risk of injury, close supervision is necessary when a machine is used near 

children. High-pressure cleaner shall not be used by children or untrained person.

WARNING:

 Know how to stop the machine and bleed pressures quickly. Be thoroughly familiar with 

the controls.

WARNING:

 Stay alert and watch what you are doing.

WARNING:

 Do not operate the machine when fatigued or under the influence of alcohol or drugs.

WARNING:

 Keep operating area clear of all persons.

WARNING:

 Do not overreach or stand on unstable support. Keep good footing and balance at all 

times.

WARNING:

 Follow the maintenance instructions specified in the manual.

WARNING:

 This machine must be grounded. If it has malfunction or breakdown, grounding provides 

a path of least resistance for electric current to reduce the risk of electric shock. The plug must be 
plugged into an appropriate outlet that is properly installed and grounded in accordance with all 
local codes and ordinances. The rating voltage (V/Hz) of the machine has to be in compliance with 
the local power supplying voltage.

WARNING:

 Check with a qualified electrician or service personnel if you are in doubt as to whether 

the outlet is properly grounded. Do not modify the plug provided with the machine. If it will not fit 
the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adapter 
with this machine.

WARNING:

 Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole 

cord connectors that accept the plug from the machine. Use only extension cords that are intended 
for outdoor use and the socket must be of watertight construction. These extension cords are 
identified by a marking "Acceptable for use with outdoor machines; store indoors while not in use." 
Use only extension cords having an electrical rating not less than the rating of the machine. Do not 
use damaged extension cords. Examine extension cord before using and replace if damaged. 
Inadequate extension cords can be dangerous. Do not abuse extension cord and do not yank on 
any cord to disconnect. Keep cord away from heat and sharp edges. Always disconnect the exten-
sion cord from the receptacle before disconnecting the machine from the extension cord.

WARNING:

 To reduce the risk of electrocution, don’t start and run the machine in the rain or storm. 

Keep all connections dry and off the ground. Do not touch plug with wet hands. It is strictly prohibi-
ted to let water leak into the machine.

WARNING: 

When the machine is turned on, the interior pumps start and continue to run even if the 

pressure wand trigger has not been depressed. Running the machine for more than 3 minutes 
without depressing the pressure wand trigger could cause heat damage to the motor and pumps, 
Please do not leave the machine running unattended or unused for more than 3 minutes.

WARNING:

 When the machine is running, please maintain a constant water supply. Without water 

circulation will damage the sealing rings of the machine.

WARNING:

 It is necessary to turn on the spray lance within one or two minutes after the machine 

has been started. Otherwise, the temperature of the circulating water within the machine will soon 
rise to a critical point, which will cause damage to the sealing rings inside the machine.

WARNING:

 Don’t start and run the machine in a place excessively cold so as to prevent the machine 

from the freezing current.

WARNING:

 This machine has been designed for only using cleaning water, do not use corrosive 

chemicals. 

WARNING: 

Use cleaning agent supplied or recommend by the manufacturer.

  

WARNING:

 High-pressure jets can be dangerous if subject to misuse.

 

 

The jet must not be directed at persons, animals, live electrical equipment or the 

 

 

machine itself. Pressure washers should not be pointed at tire walls, as it may be 

 

 

possible to damage them.

WARNING:

 Do not direct the jet against yourself or others in order to clean clothes or footwear.

WARNING:

 Disconnect from the electrical power supply before carrying out user maintenance.

If the mains cable is damaged it must be replaced by the manufacturer, or its service agent or 
similarly qualified person to avoid a hazard.

WARNING:

 Do not use the machine if a supply cord or important parts are damaged, e.g. safety 

devices, high pressure hoses, trigger gun.

WARNING:

 Be aware of the recoil caused by the water jet when the machine is switched on.

WARNING:

 When the machine is moving and installing, the machine must be in flat. When moving 

the machine, pulling the handle to move it.

WARNING:

 Connect to the water supply. The machines are not suitable for connection to portable 

water mains. Connect the machine to the water supply. (It can be a water container).
Make sure the inlet water pressure keeps between 0.01MPa and 0.4MPa.The inlet pipe should at 
least 5 M long. Do not use the pipe if the pipe is damaged. If you want connect this machine to 
portable water mains, you must install a backflow preventer in the water pipe to prevent dirty water 
flow back to the drinking water system. The backflow preventer shall comply with EN 60335-2-79 
ANNEX AA.

4. RUNNING INSTRUCTIONS

This unit is to be connected to a cold water source ONLY.
The motor of this pressure washer will NOT run. It will only operate when the trigger is squeezed.
• Connect the outlet hose to the washer and connect the spray gun to the outlet hose.
• Connect nozzle and nozzle extension.
• Check gauze filter is clear of any blockage.
• Connect the water supply hose.
• Check that the hose has no kinks in it
• Turn on water and check for leaks.  
• Depress trigger to allow air to be expelled though the pump and hoses, lock trigger.
• Plug in machine and turn on side switch.
• Unlock trigger and use the pressure washer.

5. SHUT DOWN

1. Turn off the motor(push switch to the off position).
2. Unplug the unit from the power source.
3. Turn off the water supply.
4. Press the trigger of the gun to depressurize the system, take down the water outlet hose, 10 

WARNING: 

Do not use the machine without reading the instruction sheet.

1. NAMES OF EXTERIOR PARTS

2. APPLICATION

Portable high pressure washer is a highly specialized multifunctional machine with exceptionally 
reliable safety assurance, which may be used to wash and clean cars, bikes and other outdoor 
equipment or garden patios, green houses etc.

Helpful hints for getting started
Automatic ON/OFF:

The motor on this pressure washer does not run continuously.  It only runs when the trigger of the 
spray gun is squeezed.  After following the start up procedures in this manual, turn the pressure 
washer ON and squeeze the trigger for activation.  See the section of this manual entitled “Opera-
ting Instructions” for further details on this feature.

Bleeding the gun:

It is very important to bleed the gun before using the pressure washer. Squeeze the trigger to allow 
any air that is trapped inside of the unit and hose to escape.  Continue to squeeze trigger until a 
steady stream of water comes from the nozzle.  (This process may take up to 2 minutes).  See the 
section of this manual entitled “Operating Instructions” for further details on this process.

3. SAFETY REGULATIONS  

WARNING: 

Read all the instructions before using the machine.

WARNING:

 Machines shall not be used by children. Children should be supervised to ensure that 

they do not play with the machine. This machine is not intended for use by persons (including chil-
dren) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

 

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

22

23

24

25

26

27

28

29

30

31

32

37

38

39

40

41

42

43

46

47

48

49

50

51

52

53

54

55

56

33

36

44

57

34

45

19

A

21

21

A

58

59

16

. E

X

P

L

O

D

E

D V

IE

W A

N

D S

P

A

R

E P

A

R

T L

IS

T

Summary of Contents for DAX110-1400G
















Reviews: