background image

5

¤

Saftey Interlock System.

¤Ł

Door Viewing Screen - Allows viewing of food, the screen is designed so that light can pass through,

but not the microwave.

¤Ø

Door Hook - When the door is closed, it will automatically shut. If the door is opened while the oven is

operating, the magnetron will immediately stop operating.

¤Œ

Oven Cavity 

¤º

Door Seal - Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage. 

¤

Glass Cooking Tray - Made of special heat resistant glass. Food in a proper receptacle is placed on

this tray for cooking.

¤

Roller Guide - This must always be used for cooking together with the glass cooking tray.

¤

Coupler - this fits over the shaft in the center of the oven’s cavity floor. This is to remain in the oven

for all cooking.

¤

Knob V.P.C - Used to select a microwave power level.

¤

Knob Timer - Used in setting cooking time for all functions.

¤æ

Door Release Button - By pushing this button the latch system cut off all circuits and stops the oven

before the door is opened.

¤

Reflector (Insulator Heator)

¤

Heating Element

¤

Metal Rack

FEATURES DIAGRAM

2

4

12

13

1

6

14

7

8

3

5

0

1

2

3

4

5

6

7

8

9

10

15

20

25

30

35

11

9

10

Summary of Contents for KOG-36C52S
































Reviews: