manualshive.com logo in svg

Dacor Epicure ER36D, Installation Instructions Manual, Page: 19 / 24

Share
Download
Dacor Epicure ER36D Installation Instructions Manual Download Page 19

17

Installation Instructions

Cooktop Assembly

 WARNING

Never attempt to operate the range’s cooktop with any of the 

burner rings, burner caps or grates removed.

Remove the burner rings, burner caps and grates from their 

• 

shipping packages.
Install the burners as shown. The location, type and size of 

• 

the burners varies with the range model number.
Gently set the grates on top of the spill tray. Put the legs 

• 

of each grate inside the corresponding dimples. On model 

ER36D, the largest grate goes in the center.

Crown Burner Installation

Stack Burner Installation

STEP 1

: Install 

burner head. Put 

locating tab in 

keyed hole.

STEP 1

: Put burner 

ring on top of head.

STEP 2

: Install 

burner ring. Line up 

ring tabs with head 

slots. Twist back 

and forth to assure 

proper seating.

STEP 2

: Turn ring until 

it drops into place. Twist 

back and forth to assure 

proper seating.

STEP 3

: Install burner 

caps. Ridge on cap must 

surround top of ring.

STEP 3

: Install burner 

cap. Ridge on cap must 

surround top of ring.

Burner 

head

Burner ring

Burner 

ring

Ridge on 

bottom of 

burner cap

Burner base

Burner head

Crown burner

Stack burner

Spill tray

Ridge on 

bottom of 

burner cap

Keyed

hole

Summary of Contents for Epicure ER36D

























Reviews:

No comments