background image

2

Location Requirements

IMPORTANT:

Observe all governing codes and ordinances.

• 

To ensure proper ventilation for your refrigerator, allow for 

• 

a 1/2” (13 mm) space at the top and a 1” (25 mm) space 

behind the refrigerator.
Do not install the refrigerator in a location where the 

• 

temperature will fall below 55°F (13°C).
Allow a minimum of 2 1/2” (64 mm) space between the side 

• 

of the refrigerator and an oven or range.
The floor must be able to support the refrigerator’s weight of 

• 

more than 600 lbs (272 kg), the door panels and the contents 

of the refrigerator.
The area to the left and the right of the appliance must 

• 

permit both doors to open to a minimum of 90°. Allow space 

between the side of the refrigerator doors and a corner wall 

for the handle and/or custom door panels.

Product Dimensions

The depth from the front of the door (w/o door handles) to the 

• 

back of the refrigerator chassis is 26 1/2” (673 mm).
The depth of the cabinet less the door is 23 3/4” (603 mm).

• 

The power cord is 60” (1524 mm) long.

• 

The height 

• 

from the top of the refrigerator to the floor with the 

leveling legs in the down position is 70 1/8” (1781 mm). 

Design Specifications

Installation Specifications

Tools and Parts

Make sure that you have the necessary tools and materials 

available for a proper installation:

Phillips screwdriver set

• 

Slotted screwdriver set

• 

Copper tubing for the water line. Provide sufficient length to 

• 

allow for a minimum of a 24” (610 mm) diameter service loop.
Compression nut and compression sleeve to connect to 

• 

the water supply valve. A compression nut and sleeve are 

included with the unit to connect the refrigerator side of the 

line.
Copper tubing cutter

• 

Level - 2’ (.6 m) and 4’ (1.2 m) recommended

• 

Appliance dolly able to support 700 lbs (317 kg) and 

• 

adequate manpower to handle the weight of the appliance
Nut driver set or socket set

• 

Crescent wrench

• 

Cordless drill and assorted drill bits

• 

Plywood or cardboard to protect finished flooring

• 

Appropriate materials to cover and protect the home and its 

• 

furnishings during installation

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as 

gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.

The height from the top of the refrigerator to the floor with the 

• 

leveling legs in the fully extended position is 70 3/4” (1797 

mm) at the front of the unit.
The refrigerator width from edge to edge is 35 5/8” (905 mm).

• 

The depth of the optional Epicure

• 

®

 and Millennia

®

 handles is  

2 1/2” (64 mm).

Summary of Contents for EF36IWF













Reviews: