All specifications subject to change without notice.
Phone: (800) 793-0093
www.dacor.com
PLANNING
GUIDE
DWD, ERWD, EWD, IWD, MRWD,
MWDH, MWDV, OWD, RWDV
24”, 27”, 30”, 36” Wide
Warming Drawers
Document # PG02-002
Revised 01/18/12 Page 3/3
Warming
drawer
Cooktop
1 1/2" (3.8 cm)
Typical countertop
3/4” min.*
(1.9 cm)
120 Vac
electrical
outlet
A
36" typ.
(91.4 cm)
B
C
A
Warming
drawer
Warming
drawer
B
3/4" min.*
(1.9 cm)
D
3/4" min.*
(1.9 cm)
36" typ.
(91.4 cm)
120 Vac
electrical
outlet
C
C
27"/30"/36" Dacor
single wall oven
Warming
drawer
Warming
drawer
Toe kick
D
C
C
D
120 Vac
elect.
120 Vac
elect.
A
3/4" min.*
(1.9 cm)
Cabinet/countertop tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
* Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERWD, EWD, MRWD, MWDH, MWDV and RWDV series models.
** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout.
The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout
dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the
custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below
cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.
**** Model EWD36 cannot be installed above or below another warming drawer (any type).
***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type).
Model
(A) Cutout Width
(B) Min. Width to
Adjacent Doors/
Drawers
(C) Cutout Height (D) Min. Vertical Gap
Between Cutouts
Min. Cutout Depth
DWD30
28 1/2” (72.4 cm)
30 1/4” (76.8 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
24” (61.0 cm)
ERWD27
25 1/2” (64.8 cm)
27 1/4” (69.2 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
ERWD30
28 1/2” (72.4 cm)
30 1/4” (76.8 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
EWD24
22 1/2” (57.2 cm)
24 1/4” (61.6 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
EWD27
25 1/2” (64.8 cm)
27 1/4” (69.2 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
EWD30
28 1/2” (72.4 cm)
30 1/4” (76.8 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
EWD36****
34 1/2” (87.6 cm)
36 1/4” (92.1 cm)*
9 1/8” (23.2 cm)
NA
IWD24
22 1/2” (57.2 cm)
**
9 1/8” (23.2 cm)
1 1/16” (2.7 cm)
IWD27
25 1/2” (64.8 cm)
**
9 1/8” (23.2 cm)
1 1/16” (2.7 cm)
IWD30
28 1/2” (72.4 cm)
**
9 1/8” (23.2 cm)
1 1/16” (2.7 cm)
MRWD27
25 1/2” (64.8 cm)
27” (68.6 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
MRWD30
28 1/2” (72.4 cm)
30” (76.2 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
MWDH27
25 1/2” (64.8 cm)
27 1/4” (69.2 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
MWDH30
28 1/2” (72.4 cm)
30 1/4” (76.8 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
MWDV27
25 1/2” (64.8 cm)
27 1/4” (69.2 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
MWDV30
28 1/2” (72.4 cm)
30 1/4” (76.8 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
OWD24*****
22 5/8” (57.5 cm)
24 1/4” (61.6 cm)*** 11 15/16” (30.3 cm)
NA
20 1/8” (51.1 cm)
RWDV30
28 1/2” (72.4 cm)
30 1/4” (76.8 cm)*
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
24” (61.0 cm)
WARninG
• Observe all governing codes and ordinances
during planning and installation. Contact your
local building department for further information.
• This appliance must be installed in accordance
with the accompanying installation instructions.
Mounting platform must be 3/4" (1.9 cm) thick
and support 100 lbs.
