ENGLISH
7
Installation Requirements
Electrical requirements
IMPORTANT
Observe all governing codes and ordinances.
It is the customer’s responsibility:
•
To contact a qualified electrical installer.
• To assure that the electrical installation is adequate
and in conformance with National Electrical Code,
ANSI/NFPA 70 — latest edition*, or CSA Standards
C22.1-94, Canadian Electrical Code, Part 1 and C22.2
No.0-M91 - latest edition** and all local codes and
ordinances.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
• A 120 volt, 60 Hz., AC only, 15-amp, fused electrical
circuit is required.
• If the house has aluminum wiring, follow the
procedure below.
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section
of copper wire using special connectors and/or
tools designed and UL listed for joining copper to
aluminum.
• Follow the electrical connector manufacturer’s
recommended procedure. Aluminum/copper
connection must conform with local codes and
industry accepted wiring practices.
• Wire sizes and connections must conform with the
rating of the appliance as specified on the model/
serial rating plate. The model/serial plate is located
behind the filter on the rear wall of the hood.
• Wire sizes must conform to the requirements of
the National Electrical Code, ANSI/NFPA 70 (latest
edition), or CSA Standards C22. 1-94, Canadian
Electrical Code, Part 1 and C22.2 No. 0-M91 (latest
edition and all local codes and ordinances).
Important Safety Instructions
CAUTION
To reduce risk of fi re and to properly exhaust air, be sure to duct air outside - do not vent exhaust air into spaces within
walls or ceilings, attics or into crawl spaces, or garages.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
• Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
•
Always turn the hood ON when cooking at high heat or when fl ambeing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambé).
•
Clean ventilating fans frequently. Grease should not be allowed to accumulate on the fan or fi lter.
• Use proper pan sizes. Always use cookware appropriate for the size of the surface element.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING PRECAUTIONS:*
•
SMOTHER FLAMES with a close fi tting lid, cookie sheet, or metal tray, then turn off the burner.
BE CAREFUL TO PREVENT BURNS. If the fl ames do not go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
• NEVER PICK UP A FLAMMING PAN - you may get burned.
• DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will result.
•
Use an extinguisher ONLY if:
- You know you have a class ABC extinguisher, and you already know how to operate it.
- The fi re is small and contained in the area where it started.
- The fi re department is being called.
- You can fi ght the fi re with your back to an exit.
*Based on “Kitchen Fire Safety Tips” published by NFPA.
WARNING
To reduce the risk of fi re or electrical shock, do not use this fan with any solid-state speed control device.
WARNING
Do not let children near this appliance. Do not let children play with this appliance.
Keep all packaging materials out of children’s reach. Properly dispose the packaging materials after this appliance is
unpacked.
NOTE
Suitable for use in household cooking area.
Read and save these Instructions
Summary of Contents for DHD U790LS/DA Series
Page 50: ...ESPA OL 50 Notas...
Page 51: ...ESPA OL 51 Notas...
