background image

2

Preparation

It requires at least four people to assemble a Da-Plex Semi-Rigid. To maintain optimal image geometry and screen alignment, a flat and 
straight wall free from obstructions and angular distortions should be used. 

A wall opening with 5” + the ordered viewing height and 

5” + the ordered viewing width must be used to maintain the precise in-wall fit of the Da-Plex Semi-Rigid.

 When assembling the 

screen, choose a clean work area using padded material or other soft, clean materials. The work area larger than the overall screen size 
and directly in front of or behind the wall opening where the screen is to be installed.

NOTE:

 Please read through the installation steps and note wait times. The rolled screen surface needs to be acclimated to the room for 

48 hours

 prior to installation (Step 1). Once the surface is unrolled it will need to lay in its unrolled state for 

4 hours

 

(Step 2).

Screen Orientation

Polacoat® In-Wall rigid rear projection screens have a polished surface and a matte, coated surface. The polished surface should always 
be installed so that it faces the projector and the matte surface must face the audience. If screen has anti-glare coating, the anti-glare 
surface should always face the projector.

Tools Required for Installation (not provided)

Screw Gun/Drill

1/2" Open Wrenches

(2) Ladders

#10 x 1” Flat Head Screws

¼” x 1” Hex Lag Screws

1/8” & 3/16” Hex Keys

Measuring Tape

Level

Rubber Mallet

Summary of Contents for Polacoat Da-Plex Semi-Rigid













Reviews: