background image

3

Method 2

1. Use the supplied #10 screws to attach four frame

brackets to the back of the frame as shown in
figure 5.

2. Secure the wall bracket to wall studs at the

desired height. Make sure the bracket is level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.

3. To  install the lower wall bracket, you must

measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper wall bracket to the bottom of the
lower wall bracket. See figure 6.

4. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the
inside of the roll. Place the frame over the screen
surface, and while lifting the frame with one
hand, snap the screen surface onto the frame
with the other hand while maintaining a steady
pull on the surface.

5. Position the screen with the attached surface

onto the top wall bracket as shown in figure 7.
Push down at the center of the bottom frame rail
to hook onto the lower wall bracket.

Method 3

1. Use the supplied #10 screws to attach six frame

brackets to the back of the frame as shown in
figure 8.

2. Secure the wall brackets to wall studs at the

desired height. Make sure the brackets are level.
The top of the frame will be 1/8" above the top of
the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the
screen.

3. To  install the lower wall bracket, you must

measure the overall height of the screen frame
and subtract 1/4". This is the dimension from the
top of the upper wall bracket to the bottom of the
lower wall bracket. See figure 6.

4. Some large screen sizes are made with 2-piece

side frame rails. For this type of frame you will
need to attach one High Power bracket to each
side at the joint. See figure 8.

FIGURE 5

FRAME BRACKETS
4-PIECES

#10 SCREWS
8-PIECES

WALL BRACKET
2-PIECES

FIGURE 6

OVERALL HEIGHT -1/4"

OVERALL HEIGHT

W

ALL

INSTALLATION

2

1

W

ALL

FIGURE 7

FIGURE 8

FRAME BRACKETS
6-PIECES

#10 SCREWS
12-PIECES

WALL BRACKETS
3-PIECES

HIGH
POWER
BRACKET
FOR
LARGE
SPLIT
FRAMES
ONLY.
2-PIECES

Summary of Contents for Da-Snap 74610







Reviews: