background image

4

Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted  

at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner:

NOTE: 

Use a screw driver or 5/32" allen wrench to make 

adjustments.

More screen drop

1.  Place operating switch in “down” position.

2.  When the screen stops, turn the white “down” limit knob 

(Fig.4) one-quarter turn counterclockwise. Test by raising 
picture surface approximately two feet, then lower again. 
Repeat until desired picture surface position is attained.

Less screen drop

1.  Raise picture surface approximately two feet  

above desired level.

2.  Place operating switch in “off” position.

3.  Turn the white “down” limit knob (Fig.4) one-quarter turn 

clockwise. Test by raising picture surface approximately two 
feet, then lower again. Repeat until desired picture surface 
position is attained.

 

CAUTION! Do not adjust for more drop than what was 
ordered. At least 1-1/2 wraps of fabric must remain on the 
roller. This screen comes standard with 0" or 2" black at 
the top. See the specification data sheet for details.

Boardroom Electrol

®

 Installation 120V Screens

Screen Adjustment For 120V Screens

Operating switch and  
plate furnished with 
screen. (SPDT with  
center off)

Black 

(Down)

Up

Down

Red 

(Up)

Side View of  
Switch & Box

Black (Do

wn)

R

ed (Up)

Whit

e (Common)

AC Common

Black With 
Yellow

AC Hot 
120V. AC 60 HZ
1 AMP. MAX.

NOTE: 

A single switch cannot be used to operate more than 

one screen. Contact the factory for further information.

This switch cannot be used with L.V.C.

120V Wiring Diagram

Figure 4

To junction box mounted in 
screen case, in which internal 
wiriing teminates in white, black, 
and red leads.

In multiple control 
installations the switch 
is replaced by the low 
voltage control, 
operated from push 
button stations.

Black
White
Red

Normally 
Closed 
Door 
Limit 
Switch

Motor

Off

Access 
Door

Adjustment Red 

Knob "Up"

Adjustment White 

Knob "Down"

Fabric 
Door

Screen 

Motor

Summary of Contents for Boardroom ElEctrol











Reviews: