Da-Lite ASCENDER ELECTROL Instruction Book Download

Page: 7 / 8

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate or will not

“down”

Motor does

not

hum.

Motor

hums.

Screen will not move

“up”

Motor does

not

hum

Motor

hums.

CAUSE

(a) Tripped circuit breaker.
(b) No power to operating switch

or junction.

Power at junction box

(d) Broken wire in the

“down”

position.

(e) Defective motor, limit switch or

capacitor.

(f) Capacitor burned out.

(a) Tripped circuit breaker.
(b) No power to operating switch

or junction.

Power at junction box
(c) Thermal overload tripped.

(d) Broken wire in the

“up”

position.

(e) Defective motor, limit switch

or capacitor.

(f) Capacitor burned out.

SOLUTION

(a) Reset circuit breaker.
(b) Check above. Tighten all loose

wire connections. Correct any

improper connections.

“Down” Position

Check for power across black

and white leads.

minutes. Try again.

(d) Check for continuity. Cut off old

splice and reconnect.

(e) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(f) Replace motor assembly.

(a) Reset circuit breaker.
(b) Check above. Tighten all loose

wire connections. Correct any

improper connections.

“Up” Position

Check for power across red and

white leads.

minutes. Try again.

(d) Check for continuity. Cut off old

splice and reconnect.

(e) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(f) Replace motor assembly.

Summary of Contents for ASCENDER ELECTROL









Search results

Summary of Contents for ASCENDER ELECTROL

Reviews:

Related manuals for ASCENDER ELECTROL

Brands by name

Popular brands

Da-Lite ASCENDER ELECTROL, Instruction Book

Search results

Summary of Contents for ASCENDER ELECTROL

Reviews:

Related manuals for ASCENDER ELECTROL

Brands by name

Popular brands