background image

TROUBLESHOOTING

SYMPTOM

1. No sound from any of the speakers

SOLUTION

(a) Check that receiver/amplifier is on and a source is

playing.

(b) Check that the powered subwoofer is plugged in, and

it’s Power switch is switched on (“•” position).

(c) Check all wires and connections between receiver/

amplifier and speakers. Make sure all wires are
connected. make sure none of the speaker wires are
frayed, cut or punctured, or touching each other.

(d) Review proper operation of your receiver/amplifier.

2. There is no sound coming from one speaker.

(a) Check the “Balance” control on your

receiver/amplifier.

(b) Check all wires and connections between

receiver/amplifier and speakers. Make sure all wires
are connected. Make sure none of the speaker wires
are frayed, cut or punctured, or touching each other.

(c) In Dolby Digital or DTS modes, make sure that the

receiver/processor is configured so that the speaker
in question is enabled.

(c) Turn off all electronics and switch the speaker in

question with one of the other speakers that is
working correctly. Turn everything back on, and
determine whether the problem has followed the
speaker, or has remained in the same channel. If the
problem is in the same channel, the source of the
problem is most likely with your receiver or amplifier,
and you should consult the owner’s manual for that
product for further information. If the problem has
followed the speaker, consult your dealer for further
assistance or, if that is not possible, contact Da-Lite
Screen Company.

10

3. There is no sound from the center speaker.

(a) Check all wires and connections between receiver/

amplifier and speaker. Make sure all wires are
connected. Make sure none of the speaker wires are
frayed, cut or punctured, or touching each other.

(b) If your receiver/processor is set in Dolby Pro Logic

mode, make sure the center speaker is not in
phantom mode.

(c) If your receiver/processor is set in one of the Dolby

Digital or DTS modes, make sure the receiver/
processor is configured so that the center speaker is
enabled.

Summary of Contents for ACOUSTICAL IMAGER













Reviews: