D-Link DSL-302T User Manual Download Page 56

Page: 56 / 69

DSL-302T ADSL Modem User

’

s Guide

Technical Specifications

GENERAL

Standards:

ITU G.992.1 (G.dmt)

ITU G.992.2 (G.lite)

ITU G.994.1 (G.Hs)

ITU-T Rec. I.361

ITU-T Rec. I.610

IEEE 802.3

IEEE 802.3u

IEEE 802.1d

RFC 1213 compliant

RFC 1483 (Bridged Ethernet)

RFC 1577 (IP over ATM)

RFC 1661 (PPP)

RFC 1994 (CHAP)

RFC 1334 (PAP)

RFC 2364 (PPP over ATM)

RFC 1877
(Automatic IP assignment)

RFC 2516 (PPP over Ethernet)

Supports RFC 2131 and
RFC 2132 (DHCP)

Compatible with all T1.413
issue 2 (full rate DMT over
analog POTS), and CO DSLAM
equipment

Supports ATM Forum UNI V3.1
PVC

Protocols:

TCP/IP

DHCP

AAL5

Data Transfer
Rate:

G.dmt full rate: Downstream up to 8 Mbps

Upstream up to 640 Kbps

G.lite: Downstream up to 1.5 Mbps

Upstream up to 512 Kbps

Media Interface:

RJ-11 port ADSL telephone line connection

RJ-45 port for 10/100BASET Ethernet connection

USB port

Summary of Contents for DSL-302T






































































Search results

Summary of Contents for DSL-302T

Reviews:

D-Link DSL-302T, User Manual, Page: 56 / 69

Search results

Summary of Contents for DSL-302T

Reviews: