background image

EN

G

LI

SH

Appendix - Statements

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no guarantee that interference 

will not occur in a particular installation.  If this equipment does cause harmful interference to radio 

or television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one of the following measures:

•)  Reorient or relocate the receiving antenna.

•)  Increase the separation between the equipment and receiver.

•)  Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.

•)  Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: 

Any changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate this equipment.
This device and it’s antennas(s) must not be co-located or operating in conjunction with any other 

antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of 

other channels is not possible.

This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor 

environment only.

Note: 

The country code selection is for non-US model only and is not available to all US model. Per 

FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 

This equipment should be installed and operated with minimum distance 22cm between the radiator 

& your body.

Industry Canada statement::

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de 

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas 

produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris 

un brouillage susceptible de provoquer un fonctionnement indésirable. 

Summary of Contents for DBA-1210P









Reviews: