manualshive.com logo in svg

D-Link DAP-1533, User Manual

Share
Download
D-Link DAP-1533 User Manual Download Page 73

73

D-Link DAP-1533 User Manual

Section 5 - Connecting to a Wireless Network

Connect to a Wireless Network

Using Windows® XP

Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service 

Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless 

adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows 

XP utility as seen below.

Right-click on the wireless computer icon in your system tray (lower-right 

corner next to the time). Select 

View.Available.Wireless.Networks

.

If you receive the 

Wireless.Networks.Detected

 bubble, click on the 

center of the bubble to access the utility.

 

 

 

 

 

or

The utility will display any available wireless networks in your area. 

Click on a network (displayed using the SSID) and click the 

Connect

 

button.

If you get a good signal, but cannot access the Internet, check you 

TCP/IP settings for your wireless adapter. Refer to the 

Networking.

Basics

 section in this manual for more information.

Summary of Contents for DAP-1533




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands