D-Link AP1665A1 User Manual Download Page 96 | Manualshive

Page: 96 / 99

background image

96

D-Link DAP-1665 User Manual

Appendix B - Technical Specifications

Technical Specifications

Standards

• IEEE 802.11ac

• IEEE 802.11n

• IEEE 802.11g

Security

• WPA/WPA2

- Personal

- Enterprise

Wireless Signal Rate

• Up to 1200 Mbps

Maximum Transmission Power

2

• 2.4 GHz

- 11n: 22dBm

- 11g: 22dBm

- 11b: 25dBm

Maximum Operating Voltage

- 12 V 1A

Power Consumption

• 5.18 W

Frequency Range

3

• 2.4 GHz Band:

- 2.4 - 2.4835 GHz

• 5 GHz Band:

- 5.15 GHz to 5.35 GHz

- 5.47 GHz to 5.85 GHz

Antennas

• Two 2 dBi external antennas or, two 3/5 dBi external antennas

2

LEDs

• Power

• 2.4 GHz wireless

Temperature

• Operating

- 32°F to 131°F ( 0°C to 55°C)

• Storage

- -20 to 65 °C (-4 to 149 °F)

Humidity

• Operating

- 10 - 90% (non-condensing)

• Storage

- 5 - 95% (non-condensing)

Safety & Emissions

• CE

• FCC

• TELEC

Dimensions

• 47 x 108 x 27.8 mm (5.79 x 4.25 x 1.1 inches)

Weight

• 222 grams (0.489 lbs)

1

Maximum wireless signal rate derived from IEEE Standard draft 802.11ac, 802.11n and 802.11g specifications. Actual data throughput will vary. Network conditions and

environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental

conditions will adversely affect wireless signal range.

2

All Maximum transmission power values expressed are for dual-chain mode. Maximum transmission power and included antennas may vary depending on regional regulations.

3

Range may vary depending on regional regulations.

• IEEE 802.11b

• IEEE 802.3

• IEEE 802.3u

• 5 GHz

- 11ac: 21dBm

- 11a: 21dBm

- 11n: 20dBm

• WEP

• WPS

• IC

• Wi-Fi Certified

• VCCI

• 5 GHz wireless

• LAN

«
...
94
95
96
97
98
...
»

Summary of Contents for AP1665A1




































































































Reviews:

No comments

Related manuals for AP1665A1

Brand: Ocens Pages: 2

WL-ICNAP48F-060

Brand: Mach Power Pages: 22

Brand: B-Link Pages: 14

Brand: Ruckus Wireless Pages: 4

OmniAccess Stellar AP1301 Series

Brand: Alcatel-Lucent Enterprise Pages: 2

Brand: Skyrc Pages: 2

Brand: Alvarion Pages: 9

Brand: MeshLinx Pages: 94

Rocket5AC R5AC-PTP

Brand: Ubiquiti Pages: 13

Brand: Sitecom Pages: 54

Brand: Billion Pages: 2

BiPAC 74xx series

Brand: Billion Pages: 8

Videomesh 2200 Series

Brand: Fluidmesh Pages: 30

Brand: Escene Pages: 89

Brand: Cyberoam Pages: 12

NetGenie NG11EO

Brand: Cyberoam Pages: 16

Brand: EnGenius Pages: 86

Brand: LevelOne Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands