6/36
CPS-M1
English
99.827.31 2.3/08/22
ACB interface
ACB is used for secure communication between the drive and com
-
patible D+H control systems. It enables activation, diagnostics and
configuration with perfect position, directly from the control panel. In this
process, all status messages, such as the OPEN and CLOSED signals,
opening stroke and drive errors are transmitted to the control panel.
The ACB bus is based on an open Modbus RTU protocol via which the
actuator can be directly controlled and queried.
Further information can be found in the D+H ACB Planning Manual.
Max. Number of drives per ACB connection:
AM 24
= max. 20 ACB drives
AM 230
= max. 20 ACB drives (CDC-5-ACB = max. 15)
In conjunction with locking drives (VLD, FRA),
a maximum of 10 drives (incl. locking drives) can be
connected.
Topology of the ACB bus line:
• Stub lines max. 15m
•
Total length incl. stubs max. 200m.
•
To avoid interference, the cables from the drive to the AM module
must be laid close together.
Bistable relay module - BRM-1-COC-0006
• Six user-programmable, isolated change-over contacts,
for switching signals with 24 V DC or 230 V AC
• change-over contacts as bistable version
•
Definition of a switch-off state in the event of a mains and
battery failure possible (failsafe function)
•
Integrated LEDs to indicate a fault (yellow) and alarm
(red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 2.5 mm² flexible
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
Digital I/O module - IOM-D1-1212
• 12 user-programmable digital inputs
• 12 user-programmable digital outputs
•
The digital inputs can also be parameterised as LT inputs
•
Integrated LEDs to indicate a fault (yellow) and alarm
(red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 1.5 mm² flexible
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
Actuator module - AM-1-1-08-230-D4-D2
•
Module for connecting 230 V AC actuators
•
1 group for connecting drives with a total maximum
current of 8 A
•
Up to 45 drives per AM 230 connectable
•
D+H 230 V AC drives with SHEV fast mode (HS) are
supported
•
The cable is monitored for breaks and short circuits
via the terminal module EM 230
• 2 user-programmable digital inputs (e.g. ventilation
button)
•
1 user-programmable digital output (e.g. NOT
CLOSED signal)
•
Can be used with 230 V AC standard drives
•
Adjustable ventilation time and opening width for
everyday ventilation
•
Integrated LEDs to indicate a fault (yellow) and alarm (red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 2.5 mm² flexible
(230 V AC) or 1.5 mm² flexible (24 V DC)
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
AD I/O module - ADM-AD1-1212-4
• 4 user-programmable multifunctional inputs (digital or
analog)
• 8 user-programmable digital inputs
• 12 user-programmable digital outputs
•
4 virtual adjustable threshold switches per analog input
from which a virtual user-configurable digital input is set
or reset
•
The digital inputs can also be parameterised as LT inputs
•
Integrated LEDs to indicate a fault (yellow) and alarm
(red)
• Connection using removable spring-type terminals
•
Conductor cross-sections max. 1.5 mm² flexible
• Dimensions WxHxD: 26x130x125 mm
•
Installation on a 35 mm top hat rail in combination with
an expansion module socket
