D.A.S. variant 112A User Manual Download Page 25

Page: 25 / 28

The

AXC-V112

ceiling mount accesory features

several holes on the top plate which allow for hook
clamps to be fixed to it, so up to 2 units can be
flown from truss structures.

M8x35 DIN912 screws

One slot on each side of the

AXC-V112

accessory allows for the setting of the tilt angle of
the whole cluster by means of the M8x35 screws
supplied.

AXC-AT

Truss

The

AXC-V112

can also be used to pole mount

up to one unit on top of one

variant 18A

or on a

tripod by making use of special adaptor (

AXC-ZT

AXC-V112

E) Quick release pins

Each cabinet

variant 25A/112A

includes 4 steel

heavy duty quick release pins stored on the rear
panel. Each cabinet

variant 18A

includes 6 steel

heavy duty quick release pins stored on the rear
panel.

All systems can be flown using steel/aluminium

rigging hardware located on both sides of the
cabinets. NEVER REPLACE QUICK RELEASE
PINS WITH SCREWS OR OTHER ELEMENTS!!!

Quick release pins

Manual del Usuario

/ variant /

User’s Manual

Summary of Contents for variant 112A





























Search results

Summary of Contents for variant 112A

Reviews:

Related manuals for variant 112A

Brands by name

Popular brands

D.A.S. variant 112A, User Manual

Search results

Summary of Contents for variant 112A

Reviews:

Related manuals for variant 112A

Brands by name

Popular brands