CZone 80-911-0122-00 User And Installation Manual Download Page 21

Page: 21 / 23

EN / CZone® Control 1

5 SPECIFICATIONS

TECHNICAL SPECIFICATIONS

Model

Control 1

Article numbers

80-911-0122-00

Manufacturer

BEP Marine New Zealand

Output Channels High

4 x 25A

Output Channels Low

12 x 10A Dimmable

Analogue Inputs

8 x Analogue Inputs: Positive or Negative Switching, 0-32 Volt, 0-1000 Ohm Resistance
& 4-20mA Current

Additional Monitoring

1 x Voltage Sensors (Main Positive Stud)

Circuit Protection

ATC Fuse

Alarms

Fuse Blown, Fuse In Over-ride alarms

Maximum Continuous
Current

150A @ 40°C (derating above 40°C)

NMEA 2000 Power
Consumption

Operating (All Channels On) = 100mA @ 13.2V

Operating (All Channels Off) = 75mA @ 13.2V

Power Supply

M8 (5/16") Stud Positive, M6 (1/4") Negative

Voltage

9-32V (with Power Available LED and Voltage Monitoring)

Circuit Bypass

Mechanical Protection/Bypass All Output Channels

Bilge Pump Circuits

4 x Channels High: Integrated manual control & pump running detection

Ingress Protection

IPx5 (mounted at 0°, +/-90°)

Communication

NMEA 2000

Weight

1.9kg

Certification

CE, ABYC, NMEA, ISO8846/SAEJ1171 Ignition Protected

NMEA 2000 PGN’S

NMEA 2000 PGN’s sent from the Control 1

PGN Number

Description

Fields

127508

Battery Status

Battery Voltage

127505

Fluid Level

130312

Temperature

Actual Temperature

130314

Pressure

130316

Temperature, Extended Range

Actual Temperature

Summary of Contents for 80-911-0122-00
























Search results

Summary of Contents for 80-911-0122-00

Reviews:

Related manuals for 80-911-0122-00

Brands by name

Popular brands

CZone 80-911-0122-00, User And Installation Manual

Search results

Summary of Contents for 80-911-0122-00

Reviews:

Related manuals for 80-911-0122-00

Brands by name

Popular brands