manualshive.com logo in svg

Cypress PSoC CY8C23533, Technical Reference Manual

Share
Download
Cypress PSoC CY8C23533 Technical Reference Manual Download Page 310

246

Document # 001-20559 Rev. *D

Analog Reference

21.2

Register Definitions 

The following register is associated with the Analog Reference. For a complete table of all analog registers, refer to the 

“Sum-

mary Table of the Analog Registers” on page 217

.

The register description below has an associated register table showing the bit structure. Only certain bits are accessible to
be read or written. The bits that are grayed out throughout this manual are reserved bits and are not detailed in the register
description that follows. Reserved bits should always be written with a value of ‘0’. 

21.2.1

ARF_CR Register 

The Analog Reference Control Register (ARF_CR) is used
to configure various features of the configurable analog ref-
erences.

Note

  The external bypass capacitor bit 6 (AGNDBYP) in the

Bandgap Trim register (BDG_TR: 1, EAh) controls the exter-
nal bypass capacitor. The default value is zero, which dis-
ables this function (see 

Figure 21-2

). The figure shows the

two switches in the AGND path in their default state. If bit 6
is set, then the P2[4] IO should be tri-stated and an external
capacitor connect from P2[4] to Vss.

Bit 6: HBE.  

This bit controls the 

bias

 level for all the

opamps. It operates with the power setting in each block, to
set the parameters of that block. Most applications benefit
from the low bias level. At high bias, the analog block
opamps have a faster slew rate, but slightly less voltage
swing and higher power.

Bits 5 to 3: REF[2:0].  

REF (AGND, RefHi, and RefLo) sets

the analog array reference control, selecting specific combi-
nations of voltage for analog ground and references. Many
of these reference voltages are based on the precision inter-
nal reference, a silicon bandgap operating at 1.30 volts. This
reference has good thermal stability and power supply rejec-
tion.

Alternatively, the power supply can be scaled to provide
analog ground and references; this is particularly useful for
signals that are ratiometric to the power supply voltage. See

Table 21-2

.

User supplied external precision references can be con-
nected to Port 2 inputs (available on 28 pin and larger parts).
This is useful in setting reference for specific customer appli-
cations, such as a ±1.00 V (from AGND) ADC scale. Refer-
ences derived from Port 2 inputs are limited to the same
output voltage range as the opamps in the analog blocks. 

Bits 2 to 0: PWR[2:0].  

PWR controls the bias current and

bandwidth for all of the opamps in the analog reference
block. PWR also provides on/off control in various rows of
the analog array. 

For additional information, refer to the 

ARF_CR register on

page 65

.

Add.

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,63h

ARF_CR

HBE

REF[2:0]

PWR[2:0]

RW : 00

Table 21-1.  Analog Array Power Control Bits

PWR[2:0]

CT Row

Both SC Rows

REF Bias

000b

Off

Off

Off

001b

On

Off

Low

010b

On

Off

Medium

011b

On

Off

High

100b

Off

Off

Off

101b

On

On

Low

110b

On

On

Medium

111b

On

On

High

Summary of Contents for PSoC CY8C23533



























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands