Cypress MB95710M Series Manual Download Page 57 | Manualshive

Page: 57 / 174

background image

MB95710M Series
MB95770M Series

Document Number: 002-09307 Rev. *D

Page 56 of 172

• Operation in stop mode and watch mode

• If the pin state setting bit in the standby control register (STBC:SPL) is set to “1” and the device transits to stop

mode or watch mode, the pin is compulsorily made to enter the high impedance state regardless of the DDR0 reg-
ister value. The input of that pin is locked to “L” level and blocked in order to prevent leaks due to input open. How-
ever, if the interrupt input is enabled for the external interrupt (INT00 to INT07), the input is enabled and not
blocked.

• If the pin state setting bit is “0”, the state of the port I/O or that of the peripheral function I/O remains unchanged

and the output level is maintained.

• Operation as an analog input pin

• Set the bit in the DDR0 register bit corresponding to the analog input pin to “0” and the bit corresponding to that pin

in the AIDRL register to “0”.

• For a pin shared with other peripheral functions, disable the output of such peripheral functions.

• Operation as an external interrupt input pin

• Set the bit in the DDR0 register corresponding to the external interrupt input pin to “0”.
• For a pin shared with other peripheral functions, disable the output of such peripheral functions.
• The pin value is always input to the external interrupt circuit. When using a pin for a function other than the interrupt,

disable the external interrupt function corresponding to that pin.

18.2 Port 1

Port 1 is a general-purpose I/O port. This section focuses on its functions as a general-purpose I/O port. For details of
peripheral functions, refer to their respective chapters in “New 8FX MB95710M/770M Series Hardware Manual”.

18.2.1 Port 1 configuration

Port 1 is made up of the following elements.
• General-purpose I/O pins/peripheral function I/O pins
• Port 1 data register (PDR1)
• Port 1 direction register (DDR1)
• Port 1 pull-up register (PUL1)

18.2.2 Block diagrams of port 1

• P10/UI0 pin

This pin has the following peripheral function:
• UART/SIO ch. 0 data input pin (UI0)

«
...
55
56
57
58
59
...
»

Summary of Contents for MB95710M Series















































































































































































Reviews:

No comments

Related manuals for MB95710M Series

Brand: ZKTeco Pages: 123

Brand: LANGER EMV-Technik Pages: 48

Brand: Gardena Pages: 236

Brand: Watts Pages: 17

Brand: Computer Automation Technology Pages: 55

Brand: Delta Pages: 16

Brand: Qorvo Pages: 6

Brand: Grundfos Pages: 80

Brand: Electric Time Pages: 21

1200-RD00-00-0 Series

Brand: gefran Pages: 6

Brand: National Instruments Pages: 18

Brand: Oki Pages: 92

ProCommander ES

Brand: WEIGL Pages: 12

Brand: Danfoss Pages: 24

Brand: RainFlo Pages: 8

Programmable Logic Controller DVP-SA

Brand: Delta Electronics Pages: 2

Brand: DATAEYE Pages: 10

Brand: Citizen Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands