Cypress CY8C28 series Technical Reference Manual Download Page 196 | Manualshive

Page: 196 / 571

background image

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

195

I2Cx_SCR

0,D7h

13.2.64

I2Cx_SCR

I

2

C Status and Control Register

This register is used by both master and slave to control the flow of data bytes and to keep track of the bus state during a
transfer.

Bits in this register are held in reset until one of the enable bits in I2C_CFG is set. Note that the second I

2

C block is available

in the CY8C28x03, CY8C28x23, CY8C28x43, and CY8C28x45 PSoC devices only. For additional information, refer to the

“Register Definitions” on page 497

in the I

2

C chapter

.

7

Bus Error

0

This status bit must be cleared by firmware by writing a ‘0’ to the bit position. It is never
cleared by the hardware.

1

A misplaced Start or Stop condition was detected.

6

Lost Arb

0

This bit is set immediately on lost arbitration; however, it does not cause an interrupt. This
status may be checked after the following Byte Complete interrupt. Any Start detect or a
write to the Start or Restart generate bits (I2C_MSCR register), when operating in Master
mode, will also clear the bit.

1

Lost Arbitration

5

Stop Status

0

This status bit must be cleared by firmware with write of ‘0’ to the bit position. It is never
cleared by the hardware.

1

A Stop condition was detected.

4

ACK

Acknowledge Out. This bit is automatically cleared by hardware on a Byte Complete event.
0

NAK the last received byte.

1

ACK the last received byte

3

Address

0

This status bit must be cleared by firmware with write of ‘0’ to the bit position.

1

The received byte is a slave address.

2

Transmit

Transmit bit is set by firmware to define the direction of the byte transfer. Any Start detect or a write to
the Start or Restart generate bits, when operating in Master mode, will also clear the bit.
0

Receive mode

1

Transmit mode

1

LRB

Last Received Bit. The value of the ninth bit in a Transmit sequence, which is the acknowledge bit
from the receiver. Any Start detect or a write to the Start or Restart generate bits, when operating in
Master mode, will also clear the bit.
0

Last transmitted byte was ACKed by the receiver.

1

Last transmitted byte was NAKed by the receiver.

(continued on next page)

Individual Register Names and Addresses:

0,D7h

I2C0_SCR

: 0,D7h

I2C1_SCR

: 0,E4h

7

6

5

4

3

2

1

0

Access : POR

RC : 0

RC : 0

RC : 0

RW : 0

RC : 0

RW : 0

RC : 0

RC : 0

Bit Name

Bus Error

Lost Arb

Stop Status

ACK

Address

Transmit

LRB

Byte Complete

Bit

Name

Description

«
...
194
195
196
197
198
...
»

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Brand: GE Pages: 425

Brand: Samson Pages: 48

Brand: Samson Pages: 78

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

J1000 CIMR-JC series

Brand: YASKAWA Pages: 2

Brand: YASKAWA Pages: 58

AquaLink RS All Button

Brand: Jandy Pages: 2

BoxControl Compact

Brand: elero Pages: 8

Brand: NXP Semiconductors Pages: 362

lyriQ AU7394 Series

Brand: On-Q Pages: 8

Brand: Eaton Pages: 12

Brand: Estyma Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands