Cypress CY4541 EZ-PD CCG4 Evaluation Kit Manual Download Page 46

Page: 46 / 70

Kit Operation

CY4541 EZ-

PD™ CCG4 Evaluation Kit Guide, Doc. No. 002-10353 Rev. *E

3. Connect the boards, cables, and dongles as shown in

Figure 33

if a Display Splitter board is available

Otherwise, connect

the boards to two PCs having DisplayPort outputs as shown in

Figure 34

Ensure that the monitor used supports a

DisplayPort, HDMI, VGA, or DVA interface.

Figure 33. Setup of the Dual DisplayPort Demo using a CY4541 EZ-PD CCG4 EVK and a Display Splitter Board

DC Power Adapter

(Connected to CCG

EVK Base Board 1)

DisplayPort to

DisplayPort

Cable

DisplayPort

Cable

DisplayPort

Cable

DisplayPort to

Display Port

Cable

Display Splitter

Type-C

to DP

Dongle

Type-C

to DP

Dongle

DisplayPort to

DisplayPort

Cable

DisplayPort

Summary of Contents for CY4541 EZ-PD CCG4 Evaluation Kit







































































Search results

Summary of Contents for CY4541 EZ-PD CCG4 Evaluation Kit

Reviews:

Related manuals for CY4541 EZ-PD CCG4 Evaluation Kit

Brands by name

Popular brands

Cypress CY4541 EZ-PD CCG4 Evaluation Kit, Manual

Search results

Summary of Contents for CY4541 EZ-PD CCG4 Evaluation Kit

Reviews:

Related manuals for CY4541 EZ-PD CCG4 Evaluation Kit

Brands by name

Popular brands