Cypress CP-255D, Operation Manual

Page: 1 / 12

PC/HD to 1080p
DVI Scaler Box
Operation Manual
CP-255D
Specifications:
HDMI 1.2 Compliant
Input format (Up to 165MHz) Output format (Up to 165MHz)
for CP-255D for CP-255D
* 480i 30x2 / 576i 25x2 * 480i 30x2 / 576i 25x2
Input connectors:
- YCbCr/YPbPr x 1 via 3 RCA jack
- PC RGB x 1 via 15 pin D-sub
- DVI (CP-255D)x 1
Output connector:
- DVI (CP-255D)x 1
- PC 15 pin D-sub x 1 (CP-255D)
Dimension: 180(W)x124(D)x25(H)mm
Weigh: 600gs
DC 5V 2.6 Amp
8
480i/576i
480p/576p
720p@(60/50)
1080i@(60/50)
1080p@(60/50)
VGA@(60/72/75/85)
SVGA@(56/60/72/75/85)
XGA@(60/70/75/85)
SXGA@(60/75/85)
UXGA@60
WXGA@60(1280X800)
WSXGA@60(1680X1050)
WUXGA@60(1920X1200)
Resolution
INPUT
Component D-SUB DVI/HDMI
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
*
V
V
V
V
V
V
V
V
V
V
V
V
OUTPUT
D-SUB DVI/HDMI
480i/576i
480p/576p
720p@(60/50)
1080i@(60/50)
1080p@(60/50)
VGA@(60/72/75/85)
SVGA@(56/60/72/75/85)
XGA@(60/70/75/85)
SXGA@(60/75/85)
UXGA@60
WXGA@60(1280X800)
WSXGA@60(1680X1050)
WUXGA@60(1920X1200)
Resolution
V(@60)
V(@60)
V(@60)
V(@60)
V
V
V
V
V
V
*
V
V
V
V
V(@60)
V(@60)
V(@60)
V(@60)
V(@60)
V
V
V
Table of contents
(1).Introduction........................................................................................... P1
(2).Features.................................................................................................. P1
(3).What's included.................................................................................... P1
(4).Operation Controls and Functions..................................................... P2
Front Panel............................................................................................. P2
Rear Panel............................................................................................. P2
Remote Control and functions........................................................... P3
(5).Installation.............................................................................................. P4
Input Connection................................................................................. P4
Output Connection.............................................................................. P5
(6).OSD Operation...................................................................................... P6
Specifications........................................................................................ P8
7
Note (PC): Available only when PC is selected as input.
To adjust picture quality, Use "+,-" to move the highlight bar to your desired adjust
item, press the Menu/Enter to confirm your selection.
At this point, the selected parameter will turn red, you can then use +,- to
increase or decrease the value of the parameter.
When adjustment is complete, press "Menu" to leave the parameter. Move the
highlight bar to "Exit", then press Menu/Enter to exit.
Note: The "H-position" and "V-position" are only available when component or PC
input is selected. Neither are available when the DVI input is selected.
Picture mode -there are 4 picture modes for customer to choose from.
User: Select to adjust to your favorite setting and store it.
Standard: Standard factory default setting for optimal display in a normal
environment.
Vivid: High saturation picture for optimal display in a bright room.
Movie: Picture for comfortable low brightness display in a dark room.
Scale: select overscan when input source is SD or HD video to ensure no black
band around screen border. Select underscan when input source is PC
signal to ensure full picture content fall within screen border.
Noise Reduction: This function only works when input is analog RGB or
component. It will not work for DVI input. There are four steps of
Noise Reduction-Off, Low, Middle High. The Noise Reduction will
remove the noise that results from analog to digital convertion
and digital scaling processing.
H & V position: To adjust for best horizotal and vertical position of the picture
in the screen.
6.2 Color:
User: Select to adjust to your favorite color temperature setting.
Normal: Normal color tone setting where white is pue white.
Warm: Warm color tone makes white reddish.
Cool: Cool color tone makes white bluish.
6.3 Output: The CP-255D can output a wide variety of PC and HD resolutions.
Refer to product specifications.
6.4 OSD Adjust:
H.Position: Adjust the horizontal position of the OSD graphic.
V.Position: Adjust the vertical position of the OSD graphic.
Time out: Set a predetermined time to turn off OSD menu on the screen.
Background: To select transparent or solid background of OSD graphic.
6.5 Information:
Project: Show product model number.
Input: Show input resolution i.e XGA.
Output: Show output resolution i.e 720p.
Date: Show date of firmware version.
R
0 50 100
G
0 50 100
B
0 50 100
Value of Normal
Setting
1
(1).Introduction
Congratulations on your purchase of the Cypress Video Scaler CP-255D.
Our professional Video Scaler products have been serving the industry for
many years.
In addition to Video Scalers, Cypress offers a full line of high quality PC
multimedia, Standard Converters, Video Mixer, Time Base Correctors, Video
Processors, and HDMI/DVI devices.
Please visit www.cypress.com.tw to learn more details about these products.
This manual includes operation information on the CP-255D model. Please
read this to become familiar with the CP-255D and keep the manual for
possible reference in the future.
Cypress's CP-255D is designed to convert PC, SD, HD and DVI to digital DVI at
a variety of HDTV and PC resolutions. It handles input and output signal at 205
MHZ ultra high bandwidth. Cypress CP-255D has many great features to
enhance video performance and is ideal for use in professional large screen
presentation.
(2).Features
1. CP-255D is a high bandwidth and professional PC/Component/DVI to DVI
Scaler that accepts PC RGB (up to UXGA), HD Component (480i up to
1080p) and DVI (up to WUXGA) and scale them up to DVI-I output
(1080p/WUXGA).
2. The input to the CP-255D is analog PC or HDTV signal in the format of
either RGBHV, YPbPr, (YCbCr) or digital DVI.
3. The output of the CP-255D is digital DVI plus analog PC/HD with
selectable output resolution from 480i to 1080p and VGA to WUXGA.
4. The input resolution is automatically detected while the output resolution
and refresh rate can be selected through OSD menu or front panel push
buttons.
5. Native output resolution ensures most optimal display resolution on your
screen. When "Native" is selected as the output resolution, the CP-255D will
automatically detect the native resolution of the display and send out the
most optimal pixel timing to match TV's final display resolution.
6. Output picture adjustment on brightness, contrast, color, RGB level, and
H-V position.
7. The DVI input is HDCP compliant which means if input is HDCP encrypted
then DVI output is also HDCP encripted. In this case the PC analog output
will be turned off.
8. Includes advanced features such as Noise Reduction and overscan/
underscan adjustment.
(3).What's included
The following items are included in the standard package.
1. PC/HD/DVI to DVI scaler box.
2. VGA cable x 1
3. YPbPr 3RCA cable x 1
4. AC power adaptor 5V/ 2A, center positive.
6
(6).OSD Operation
After power on the unit, press the "menu" button will bring up the main
menu as follows:
Video (or PC)
Color
Output
OSD
Info
Use +, - button to move hightlight bar to your desired parameter, then press
MENU/ENTER to enter into sub-menu of your selected parameter.
6.1 Video (or PC): When Video is selected a sub menu as below comes up.
Contrast
Brightness
Hue
Saturation
Sharpness
Picture Mode
Scale
NR
H-position (PC)
V-position (PC)
Exit
Main Menu
Video(PC) Color Output OSD Info
Contrast
Brightness
Hue
Sat
Sharpness
Picture Mode
Scale
NR
(H-positon)
(V-postion)
Exit
User
Normal
Warm
Cool
VGA
SVGA
XGA
SXGA
UXGA
WXGA
WSXGA
WUXGA
480i
480p
576i
576p
720p(50/60)
1080i(50/60)
1080p(50/60)
NATIVE
H.Position
V.Position
Time out
Background
Exit
Project
Input
Output
Date
user
standard
vivid
movie
overscan
underscan
Letterbox
Panscan
Full
low
middle
high
off
2
YPbPr (YCbCr) PC DVI
(4).Operation Controls and Functions
Front Panel
1. Power: Press the button to turn ON or turn OFF (standby) the power of the unit.
2. Menu/Enter: This button serves two purposes.
a. Press the button to bring up OSD main menu as shown in the
"OSD Operation". (page 7)
b. To act as a "Enter" key to enter sub menu or to adjust setting value of the
selected parameter.
3. +/- button:
The buttons provide 3 functions:
a. Input select ("+"): Press the "+" button repeatedly to select your desired
input source. The input sources are toggled through in the following
sequence.
b. Auto Tune ("-"): Press the "-" button to carry out picture auto adjust for
analog inputs (component or PC). The CP-255D will fine tune the position
(centering) and color of the output picture.
c. When in the OSD menu mode: Press the +, - button to move up or down
the highlight bar to your desired parameter. Or once a parameter is
selected with MENU/Enter button, press the button to adjust setting value
of your selected parameter.
4. Input LED Indicators: When one of the LED illuminates its corresponding source
is being selected as input.
5. IR Sensor: Infrad remote control sensor.
6. Component Input: Connects this input connector to the Component output
connector of your source equipment using the enclosed 3RCA to 3RCA
cable.
The CP-255D accepts both interlaced component input (480i, 576i) and
deinterlaced progressive input (480p, 576p...1080p).
The input range is 480i, 570i~1080i, 1080p.
Rear Panel
1. PC input: Connects this PC input connector to the VGA output of your
PC. The acceptable PC resolutions range from VGA~WUXGA.
5
The CP-255D accepts component, PC and DVI inputs. The formats supported by
these inputs are as follows:
- When connecting to a PC source use a 15-pin D-sub cable to connect the
output of a PC to the D-Sub input connector of the CP-255D.
- When connecting to a component source (either SD or HD resolution) use a
3RCA to 3RCA cable to connect the YPbPr or YCbCr output of a DVD or Set Top
Box to the Y-Cb/Pb-Cr/Pr input connecter of the CP-255D.
- When connecting to a DVI source, use a DVI-I or DVI-D cable to connect the
DVI output of a PC or DVD to the DVI input connector of the CP-255D.
- When connecting to a HDMI source, use a HDMI cable to connect to the HDMI
output of a HDMI source, such as DVD or STB, on the one end.
And use a HDMI to DVI connector adaptor to connect to the other end of the
HDMI cable. The DVI connector of the adaptor is then connect to the DVI input
of the CP-255D.
The CP-255D can automatically detect the input resolution of all three inputs.
To switch from one input source to another just press the input button on the
front panel ("+") or on the remote control.
Output Connection
The CP-255D can output a variety of PC, SD and HD resolutions in both digital and
analog format simultaneously.
The digital output is available from the DVI output connector while the analog
output is available from the PC D-sub output connector.
1 2 5 3 6 4
Y/HD
Cb/Pb
Cr/Pr
HD PC DVI
MENU POWER INPUT
ENTER
-
+
INPUT
AUTO
ADJUST
5 4 3 2 1
PC OUT DVI OUT PC IN DVI IN
DC 5V
HDMI TV
HDMI TV LCD TV
LCD
or
Monitor
or
DVI
Cable
or DVI Cable
RGBHV
DVI to HDMI
connector
adaptor
PC OUT DVI OUT PC IN DVI IN DC 5V
3
Component PC DVI
2
3
6
8
10
11
1
5
4
7
9
12
2. DVI input: Connects this DVI input connector to the DVI output connector of
your DVI source equipment. The DVI input should be digital DVI only and
should not include analog RGB signal.
The use of DVI-I connector is to ensure both DVI-I and DVI-D male connector
of the DVI cable can fit into this input connector. The digital DVI input
resloution can range from 480i~1080p, or VGA~WUXGA.
3. PC-D sub out: The connector for scaled analog RGB output.
Connect this output port to the analog PC RGB input of your monitor, or
connect it to the RGBHV input of your HD display using D-sub to 5 BNC
adaptor cable. (not included in the package)
Note: When input is a HDCP encrypted DVI signal this analog output will be
turned off.
4. DVI output: Scaled digital DVI output. Connect this output to the DVI input or
HDMI input of your Digital display.
Note: When input is a HDCP encrypted DVI signal the DVI output is also HDCP
encrypted. The monitor/display that connected to this output also need to
be HDCP compliant in order to get a nice and clean picture. A non-HDCP
compliant display can only display non-HDCP signal and picture will
become noise when input is a HDCP-encrypted signal.
5. Power jack: Connect to the 5V 2A DC power adaptor.
Remote Control and functions:
1. Power: Press the button once to power on the CP-255D. Press again to enter
standby mode.
2. Input: Press the button repeatedly to toggle through various input sources as
follows.
3. HD input: Press the button to select component input.
4. PC input: Press the button to select PC input.
5. HDMI/DVI input: Press the button to select DVI (or HDMI) input.
6. Output resolution:
Select buttons: Press any one of the button to directly
select output resolution.
For other output resolutions that are not
covered by these buttons please enter
Menu/Output page to select them.
7. MENU: Press the button to bring up OSD main menu page.
8. Exit: Press the button to exit from a sub menu or main
menu.
9. Up/Down/Left/Right: Press the Up/Down button to move
the highlight bar to your desired
parameter during the OSD operation.
Press the Left/Right button to increase/
decrease the setting value of a
selected parameter.
4
10. OK (Enter): Press the button to confirm your selection.
11. Reset: Press the button to reset the unit's firmware setting to the factory
default value.
12. Auto Adjust: Press the button to optimize the position of the picture
(picture centering) on the screen.
(5).Installation
Input Connection
PC OUT DVI OUT PC IN DVI IN DC 5V
HDMI
HDMI
HDMI
HDMI
Cable
DVI
HDMI out
DVD
DVI out
PC
STB
PC
or
DVI
Cable
PC-in
HDMI to DVI
connector
adaptor
Component out
DVD or Set Top Box
Component in
Y/HD
Cb/Pb
Cr/Pr
HD PC DVI
MENU POWER INPUT
ENTER
-
+
INPUT
AUTO
ADJUST