manualshive.com logo in svg

Cypress CapSense Express SmartSense CY3280-MBR2, Manual

Share
Download
Cypress CapSense Express SmartSense CY3280-MBR2 Manual Download Page 34

34

CY3280-MBR2 CapSense Express with SmartSense Auto-Tuning Kit Guide, Doc. # 001-71857 Rev. *C

Hardware

4.4

Connector Details

4.4.1

USB-IIC Connector

This kit is configurable through the IIC interface. The USB-IIC connector enables the kit to connect to
the PC via the USB cable provided with the kit. This connector serves two main purposes:

■

Enables powering the kit from the GUI

■

Enables configuring the kit by connecting to the GUI via the USB-IIC header

4.4.2

Expansion Connector 

Table 4-2

 shows various signals connected to the 44-pin expansion connector. The CS inputs (CS0-

CS9) and GPOs linked to each CapSense button are brought to the 44-pin expansion connector.
This is used to verify SmartSense Auto-Tuning by connecting the Flex-PCB, BSM, or any other con-
necting board. The kit can be powered from an external power supply using the VDD and GND sig-
nals available in the connector. The kit also has output lines for host control and buzzer. The IIC
clock and data lines from the CY8CMBR2110 chip are also brought to this connector.

Note: 

There are two pins assigned to each of GPO3 and GPO5. This is done to make expansion

connector compatible to CY3280 Universal CapSense Module Boards.

Table 4-2.  44-Pin Expansion Connector

Pin

Connected to

Pin

Connected to

P1-1

CS8

P1-23

Wake

P1-2

GPO8

P1-24

GPO 1

P1-3

CS5

P1-25

GND

P1-4

XRES

P1-26

GND

P1-5

GPO5

P1-27

CS6

P1-6

GND

P1-28

GPO6

P1-7

GPO5

P1-29

GPO3

P1-8

GPO2

P1-30

CS3

P1-9

CS2

P1-31

GPO3

P1-10

CS9

P1-32

NC

P1-11

GPO9

P1-33

CS0

P1-12

GPO7

P1-34

GND

P1-13

CS7

P1-35

GND

P1-14

CS4

P1-36

GND

P1-15

GND

P1-37

I2C SDA

P1-16

GND

P1-38

I2C SCL

P1-17

CS1

P1-39

GND

P1-18

Host Cntl 0

P1-40

GND

P1-19

Host Cntl 1

P1-41

VDD Dev

P1-20

GPO4

P1-42

NC

P1-21

Buzzer Out 0

P1-43

VDD Ext

P1-22

Buzzer Out 1

P1-44

NC

Summary of Contents for CapSense Express SmartSense CY3280-MBR2

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands