Cygnus M3-DIVE Operation Manual Download Page 25

Page: 25 / 117

Cygnus DIVE Operating Manual

M3-DIVE-M-ENG_Iss9.docx

Page 25 of 117

Notes.

Thicknesses stated are for steel with a velocity of 5920 m/s (0.2331 in/

s), this

will vary with different metals/materials.

S2C Probe using Deep Coat mode to measure through thick coatings.

T5B & T2C Probes will include any coating thickness in the metal thickness
measurement when used in Single Echo mode.

Single Element Probes and Protective Membranes

All Cygnus single element probes have a soft face and are
therefore fitted with a Polyurethane Membrane which provides

better contact on rough surfaces and protects the probe face from
wear, prolonging the life of the probe.

Check the membrane regularly as it is important the membrane is
changed as soon as it shows any signs of wear.

Single Element Probe Membrane Parts.

Single Element Probe Membrane Locking Key

Probe Body

Locking Ring

Polyurethane Membrane
Knurled Ring

Summary of Contents for M3-DIVE






















































































































Search results

Summary of Contents for M3-DIVE

Reviews:

Related manuals for M3-DIVE

Brands by name

Popular brands

Cygnus M3-DIVE, Operation Manual

Search results

Summary of Contents for M3-DIVE

Reviews:

Related manuals for M3-DIVE

Brands by name

Popular brands