Cygnus M3-DIVE Operation Manual Download Page 17

Page: 17 / 117

Cygnus DIVE Operating Manual

M3-DIVE-M-ENG_Iss9.docx

Page 17 of 117

The probe connector can be plugged into

either of the connectors on the DIVE
gauge body depending on which arm the
DIVE gauge is worn on.

The connector is a simple push-fit. The
white dots must be aligned for the
connectors to mate.

To release the probe connector you must
pull back the connector front part of the

body (A) as you pull the connector out of the
gauge body.

If the connector appears tight push the back

part (B) in towards the gauge while pulling
back on the front part (A).

Probe Calibration Check Message

If you connect a probe while the gauge is
turned on a message reminding you to
check the calibration will be displayed.

Press either button to continue.

Summary of Contents for M3-DIVE






















































































































Search results

Summary of Contents for M3-DIVE

Reviews:

Related manuals for M3-DIVE

Brands by name

Popular brands

Cygnus M3-DIVE, Operation Manual

Search results

Summary of Contents for M3-DIVE

Reviews:

Related manuals for M3-DIVE

Brands by name

Popular brands