manualshive.com logo in svg

CycleOps 200 Pro Series, User Manual, Page: 11 / 15

Share
Download
CycleOps 200 Pro Series User Manual Download Page 11

10

Adjust Flywheel/Chain Tension 

Over time and after substantial use, the chain on the CycleOps Pro Series indoor cycle will stretch.  Adjusting the tension/

alignment is a difficult task and improper adjustment can lead to premature chain/cog wear.  It is recommended this task 

be done with assistance from an authorized indoor cycle dealer. The chain tension has been adjusted properly when there 

is little or no play felt when the pedals are rocked back and forth. 

NOTE: Be sure to make small incremental adjustments to the tensioning hardware on both sides of the flywheel. Only 

adjusting one side will lead to improper flywheel alignment and unwanted drive train wear and/or noise. 

CAUTION: Improper chain adjustment will cause premature wear and may void the warranty. 

CAUTION: NEVER put hands into or near the drive train while it is motion! 

1. Using a 4mm Allen wrench, remove 

the three chain guard bolts. 

 3. Use a 17mm cone wrench to hold 

the axle locking nuts in place.  Do not 

turn the wrench, it is only used as a 

stabilizer. With the other hand, use a 

15mm box wrench to loosen the flange 

nuts on the axle.  Repeat this process 

on each side of the flywheel.

4. Using a 10mm box wrench, adjust 

the tensioning hardware until the 

proper chain tension is achieved evenly 

on both sides.

5. Pull chain down (midway between 

chain

ring and gear) to measure vertical 

travel. Vertical travel should be approxi-

mately 

1/4” when the chain has been properly 

adjusted. Tighten flange nuts to 75 in-

lbs. Do not overtighten. 

10 mm tensioning 

hardware

Flange Nut

Axle Lock 

Nut

Vertical 

Travel 

2. Pull chain down (midway between 

chain ring and gear) to measure verti-

cal travel. Vertical travel should be 

approximately 1/4”.  Vertical travel with 

significantly more or less than 1/4” 

should be adjusted. 

 

Vertical 

Travel 

Summary of Contents for 200 Pro Series
















Reviews:

No comments